pnx1700 NXP Semiconductors, pnx1700 Datasheet - Page 286
pnx1700
Manufacturer Part Number
pnx1700
Description
Connected Media Processor
Manufacturer
NXP Semiconductors
Datasheet
1.PNX1700.pdf
(832 pages)
- Current page: 286 of 832
- Download datasheet (8Mb)
Philips Semiconductors
Volume 1 of 1
PNX17XX_SER_1
Preliminary data sheet
2.4.1 GPIO Frequency Restrictions
system memory must have consumed the 64-byte memory before the GPIO logic
needs it again. If the system memory latency is too long then the GPIO logic does not
have an internal 64-byte memory to store in-coming data. In that case GPIO module
generates an internal overrun, INT_OE, interrupt. If pattern generation mode the
Underrun condition is not flagged to the CPU.
If either a FIFO_OE or INT_OE or Underrun error occurs, signal monitoring is
temporarily halted, and incoming timestamps/samples will be lost. In the case of
FIFO_OE, sampling resumes as soon as the control software makes one or more
new buffers available by clearing the relevant BUFx_RDY. In the case of INT_OE, the
GPIO module resumes normal operation as soon as the system memory allows it.
INT_OE and FIFO_OE are ‘sticky’ error flags meaning they will remain set until an
explicit software write of logic ‘1’ to FIFO_OE_CLR or INT_OE_CLR is performed. In
the case of Underrun the GPIO module resumes as soon as data is available.
The GPIO module has two frequency limitations:
One FIFO Enabled
The calculations below show the maximum frequencies allowed for signals to be
monitored and patterns to be generated if only one FIFO queue is enabled and the
minimum latency guarantied by the system is 40 s.
Remark: Sampling calculations assume 1-bit sampling (EN_IO_SEL = 00 or 11).
Timestamping: 1 edge -> 32-bits
=> 16 edges = 64 bytes of data
=> 16 edges can occur every 40 s
=> 1 edge can occur every 2.5 s = 400 kHz maximum frequency.
Sampling: 1 edge -> 1bit
=> 512 edges = 64 bytes of data
=> 512 edges can occur every 40 s
=> 1 edge can occur every 78.125 ns = 12.8 MHz maximum frequency.
•
•
A hardware limitation: the maximum clock used to sample signals or generate
patterns is 108 MHz.
A hardware/software limitation: the system memory latency prevents to fill or
empty the internal 64-byte memories on time. This is not only a hardware
limitation. Indeed the memory latency is dependant on the memory clock speed,
the amount of bandwidth used by the other modules of the PNX17xx Series
system and ultimately by the central internal arbiter settings.
Rev. 1 — 17 March 2006
Chapter 8: General Purpose Input Output Pins
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
PNX17xx Series
8-15
Related parts for pnx1700
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: