pnx1700 NXP Semiconductors, pnx1700 Datasheet - Page 755
pnx1700
Manufacturer Part Number
pnx1700
Description
Connected Media Processor
Manufacturer
NXP Semiconductors
Datasheet
1.PNX1700.pdf
(832 pages)
- Current page: 755 of 832
- Download datasheet (8Mb)
Philips Semiconductors
Volume 1 of 1
PNX17XX_SER_1
Preliminary data sheet
3.1.1 Handshaking and Communication Protocol
The following describes the mechanism for transferring data via JTAG.
Transfer from Debug Front-End to Debug Monitor
The debugger front-end running on a host transfers data to a debug monitor via the
TM_DBG_DATA_IN register. It must poll the TM_DBG_CTRL2.ifull bit to check if the
TM_DBG_DATA_IN register can be written to. If the TM_DBG_CTRL2.ifull bit is clear,
the front-end may scan data into the TM_DBG_DATA_IFULL_IN register.
Note that data and control bits may be shifted in with SEL_IFULL_IN instruction and
the bit shifted into TM_DBG_CTRL2.ifull register must be 1. This action triggers an
interrupt. The debug monitor must copy the data from TM_DBG_DATA_IN register
into its private area when servicing the interrupt and then clear the
TM_DBG_CTRL2.ifull bit. This allows the JTAG interface module to write the next
piece of data to the TM_DBG_DATA_IN register.
Transfer from Monitor to Front-End
The monitor running on TM5250 must check if TM_DBG_CTRL1.ofull is clear and if
so, it can write data to TM_DBG_DATA_OUT. After that, the monitor must set the
TM_DBG_CTRL1.ofull bit. The debugger front-end polls the TM_DBG_CTRL1.ofull
bit. When set, it can scan out the TM_DBG_DATA_OUT register and clear the
TM_DBG_CTRL1.ofull bit. Since TM_DBG_DATA_OUT is read-only via JTAG, the
update action at the end of scan out has no effect on TM_DBG_DATA_ OUT. The
TM_DBG_CTRL1.ofull bit however, must be cleared by shifting in the value 1.
Controller States
In the power on reset state, TM_DBG_CTRL2.ifull, TM_DBG_CTRL1.ofull and
TM_DBG_CTRL1.sleepless bits are cleared.
Example of Data Transfer via JTAG
Scanning in a 5-bit instruction will take 12 TCK cycles from the Run-Test/Idle state:
Likewise, scanning in a 32-bit data register will take 38 TCK cycles, and transferring
an 8-bit TM_DBG_CTRL data register will take 14 TCK cycles from Idle state.
However, if a data transfer follows instruction transfer, then the transition to DR scan
stage can be done without going through Idle state, thereby saving 1 cycle.
•
•
•
•
•
4 cycles to reach Shift-IR state
5 cycles for actual shifting in
1 cycle to exit1-IR state
1 cycle to update-IR state,
1 cycle back to Run-Test/Idle state.
Rev. 1 — 17 March 2006
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Chapter 24: TM5250 Debug
PNX17xx Series
24-5
Related parts for pnx1700
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: