AGL015 MICROSEMI [Microsemi Corporation], AGL015 Datasheet - Page 18

• Manufacturer Part Number: AGL015
• Description: IGLOO Low Power Flash FPGAs with Flash*Freeze Technology
• Manufacturer: MICROSEMI [Microsemi Corporation]

IGLOO DC and Switching Characteristics
Table 2-2 •
Table 2-3 •
2- 2
Product
Grade
Commercial
Industrial
Notes:
1. This is a stress rating only; functional operation at any condition other than those indicated is not implied.
2. These limits apply for program/data retention only. Refer to
Symbol
T
T
VCC
VJTAG
VPUMP
VCCPLL
VCCI and
VMV
Notes:
1. All parameters representing voltages are measured with respect to GND unless otherwise specified.
2. To ensure targeted reliability standards are met across ambient and junction operating temperatures, Microsemi
3. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
4. All IGLOO devices (V5 and V2) must be programmed with the VCC core voltage at 1.5 V. Applications using the V2
5. For IGLOO
6. For IGLOO V2 devices only, operating at VCCI ≥ VCC.
7. VPUMP can be left floating during operation (not programming mode).
8. VCCPLL pins should be tied to VCC pins. See the "Pin Descriptions" chapter of the
9. VMV pins must be connected to the corresponding VCCI pins. See the "Pin Descriptions" chapter of the
10. 3.3 V wide range is compliant to the JESD-8B specification and supports 3.0 V VCCI operation.
A
J
conditions and absolute limits.
recommends that the user follow best design practices using Microsemi’s timing and power simulation tools.
standard are given in
devices powered by 1.2 V supply must switch the core supply to 1.5 V for in-system programming.
for further information.
Fabric User’s Guide
3
9
8
Ambient Temperature
Junction Temperature
1.5 V DC core supply voltage
1.2 V–1.5 V wide range DC
core supply voltage
JTAG DC voltage
Programming voltage
Analog power supply (PLL)
1.2 V DC core supply voltage
1.2 V DC wide range DC
supply voltage
1.5 V DC supply voltage
1.8 V DC supply voltage
2.5 V DC supply voltage
3.0 V DC supply voltage
3.3 V DC supply voltage
LVDS differential I/O
LVPECL differential I/O
Recommended Operating Conditions
Flash Programming Limits – Retention, Storage, and Operating Temperature
®
V5 devices
Programming
Cycles
for further information.
Table 2-25 on page
500
500
6
4,6
2
10
Program Retention
(biased/unbiased)
Parameter
5
6
2-24. VCCI should be at the same voltage within a given I/O bank.
20 years
20 years
Programming Mode
Operation
1.5 V DC core supply voltage
1.2 V – 1.5 V DC core supply
voltage
4,6
1
7
R ev isio n 1 9
Temperature T
Table 2-1 on page 2-1
Maximum Storage
110
110
5
STG
1.425 to 1.575 1.425 to 1.575
1.425 to 1.575
2.375 to 2.625
(°C)
1.425 to 1.575 1.425 to 1.575
1.14 to 1.575
1.14 to 1.575
1.14 to 1.575
Commercial
3.15 to 3.45
1.14 to 1.26
2.7 to 3.6
1.4 to 3.6
1.7 to 1.9
2.3 to 2.7
3.0 to 3.6
3.0 to 3.6
0 to +70
0 to +85
0 to 3.6
2
IGLOO FPGA Fabric User’s Guide
and
Maximum Operating Junction
Table 2-2
Temperature T
1.425 to 1.575
2.375 to 2.625
1.14 to 1.575
1.14 to 1.575
1.14 to 1.575
–40 to +100
3.15 to 3.45
1.14 to 1.26
1
Industrial
–40 to +85
2.7 to 3.6
1.4 to 3.6
1.7 to 1.9
2.3 to 2.7
3.0 to 3.6
3.0 to 3.6
for device operating
0 to 3.6
100
100
IGLOO FPGA
J
(°C)
Units
2
°C
°C
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V