MT41J64M16LA-187E:B TR Micron Technology Inc, MT41J64M16LA-187E:B TR Datasheet - Page 113

• Manufacturer Part Number: MT41J64M16LA-187E:B TR
• Description: IC DDR3 SDRAM 1GBIT 96FBGA
• Manufacturer: Micron Technology Inc
• Type: DDR3 SDRAMr

Specifications of MT41J64M16LA-187E:B TR

• Format - Memory: RAM
• Memory Type: DDR3 SDRAM
• Memory Size: 1G (64M x 16)
• Speed: 533MHz
• Interface: Parallel
• Voltage - Supply: 1.425 V ~ 1.575 V
• Operating Temperature: 0°C ~ 95°C
• Package / Case: 96-FBGA
• Organization: 64Mx16
• Density: 1Gb
• Address Bus: 16b
• Maximum Clock Rate: 1.066GHz
• Operating Supply Voltage (typ): 1.5V
• Package Type: FBGA
• Operating Temp Range: 0C to 95C
• Operating Supply Voltage (max): 1.575V
• Operating Supply Voltage (min): 1.425V
• Supply Current: 265mA
• Pin Count: 96
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 557-1378-2

Commands
DESELECT
NO OPERATION
ZQ CALIBRATION LONG
ZQ CALIBRATION SHORT
ACTIVATE
READ
PDF: 09005aef826aa906
1Gb_DDR3_SDRAM.pdf – Rev. J 05/10 EN
The DESELT (DES) command (CS# HIGH) prevents new commands from being execu-
ted by the DRAM. Operations already in progress are not affected.
The NO OPERATION (NOP) command (CS# LOW) prevents unwanted commands from
being registered during idle or wait states. Operations already in progress are not affected.
The ZQ CALIBRATION LONG (ZQCL) command is used to perform the initial calibra-
tion during a power-up initialization and reset sequence (see Figure 50 (page 129)).
This command may be issued at any time by the controller depending on the system
environment. The ZQCL command triggers the calibration engine inside the DRAM. Af-
ter calibration is achieved, the calibrated values are transferred from the calibration
engine to the DRAM I/O, which are reflected as updated R
The DRAM is allowed a timing window defined by either
the full calibration and transfer of values. When ZQCL is issued during the initialization
sequence, the timing parameter
plete, subsequent ZQCL commands require the timing parameter
The ZQ CALIBRATION SHORT (ZQCS) command is used to perform periodic calibra-
tions to account for small voltage and temperature variations. The shorter timing
window is provided to perform the reduced calibration and transfer of values as defined
by timing parameter
0.5% R
sitivities specified in Table 41 (page 64) and Table 42 (page 64).
The ACTIVATE command is used to open (or activate) a row in a particular bank for a
subsequent access. The value on the BA[2:0] inputs selects the bank, and the address
provided on inputs A[n:0] selects the row. This row remains open (or active) for access-
es until a PRECHARGE command is issued to that bank.
A PRECHARGE command must be issued before opening a different row in the same bank.
The READ command is used to initiate a burst read access to an active row. The address
provided on inputs A[2:0] selects the starting column address depending on the burst
length and burst type selected (see Burst Order table for additional information). The
value on input A10 determines whether or not auto precharge is used. If auto precharge
is selected, the row being accessed will be precharged at the end of the READ burst. If
auto precharge is not selected, the row will remain open for subsequent accesses. The
value on input A12 (if enabled in the mode register) when the READ command is issued
ON
and R
TT
impedance error within 64 clock cycles, assuming the maximum sen-
t
ZQCS. A ZQCS command can effectively correct a minimum of
113
t
ZQinit must be satisfied. When initialization is com-
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1Gb: x4, x8, x16 DDR3 SDRAM
t
ZQinit or
ON
and ODT values.
© 2006 Micron Technology, Inc. All rights reserved.
t
ZQoper to be satisfied.
t
ZQoper to perform
Commands