P89V51RC2FN,112 NXP Semiconductors, P89V51RC2FN,112 Datasheet - Page 20

• Manufacturer Part Number: P89V51RC2FN,112
• Description: IC 80C51 MCU FLASH 32K 40-DIP
• Manufacturer: NXP Semiconductors
• Series: 89Vr

Specifications of P89V51RC2FN,112

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89V5x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1017 - BOARD 44-ZIF PLCC SOCKET622-1001 - USB IN-CIRCUIT PROG 80C51ISP
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-2430-5; 935278782112; P89V51RC2FN

NXP Semiconductors
P89V51RB2_RC2_RD2_5
Product data sheet
6.3.1 Flash organization
6.3.2 Boot block (block 1)
6.3 Flash memory IAP
Table 10.
Not bit addressable; Reset value 00H
Table 11.
The P89V51RB2/RC2/RD2 program memory consists of a 16/32/64 kB block. ISP
capability, in a second 8 kB block, is provided to allow the user code to be programmed
in-circuit through the serial port. There are three methods of erasing or programming of
the flash memory that may be used. First, the flash may be programmed or erased in the
end-user application by calling low-level routines through a common entry point (IAP).
Second, the on-chip ISP bootloader may be invoked. This ISP bootloader will, in turn, call
low-level routines through the same common entry point that can be used by the end-user
application. Third, the flash may be programmed or erased using the parallel method by
using a commercially available EPROM programmer which supports this device.
When the microcontroller programs its own flash memory, all of the low level details are
handled by code that is contained in block 1. A user program calls the common entry point
in the block 1 with appropriate parameters to accomplish the desired operation. Boot block
operations include erase user code, program user code, program security bits, etc.
Bit
7 to 4
3
2
1
0
Bit
Symbol
Fig 7. Dual data pointer organization
AUXR1 - Auxiliary register 1 (address A2H) bit allocation
-
AUXR1 - Auxiliary register 1 (address A2H) bit description
Symbol
-
GF2
0
-
DPS
7
DPS = 0
DPS = 1
AUXR1 / bit0
-
Rev. 05 — 12 November 2009
DPS
6
DPTR0
DPTR1
Description
Reserved for future use. Should be set to ‘0’ by user programs.
General purpose user-defined flag.
This bit contains a hard-wired ‘0’. Allows toggling of the DPS bit by
incrementing AUXR1, without interfering with other bits in the register.
Reserved for future use. Should be set to ‘0’ by user programs.
Data pointer select. Chooses one of two Data Pointers for use by the
program. See text for details.
-
5
DPH
83H
-
P89V51RB2/RC2/RD2
4
DPL
82H
8-bit microcontrollers with 80C51 core
DPTR1
DPTR0
GF2
3
external data memory
0
2
002aaa518
-
© NXP B.V. 2009. All rights reserved.
1
DPS
20 of 80
0