MC9S12HZ128VAL Freescale Semiconductor, MC9S12HZ128VAL Datasheet - Page 665

• Manufacturer Part Number: MC9S12HZ128VAL
• Description: IC MCU 16BIT 2K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12HZ128VAL

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, I²C, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 112-LQFP
• Processor Series: S12H
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 6 KB
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

E.2
The ROM module provides the necessary security information to the rest of the chip. After each reset, the
ROM module determines the security state of the microcontroller as defined in section
“ROM Options Register
If the NVM Options byte at 0xFF0F in the NVM Options Field is in secure state, any reset will cause the
microcontroller to return to the secure operating mode
E.2.1
Security is engaged or disengaged based on the state of two non-volatile register bits (SEC1:SEC0) in the
ROPT register. During reset, the contents of the non-volatile location NVOPT are copied from ROM into
the working ROPT register in high-page register space.
A user engages security by defining the security bits in the NVOPT location to select security enabled. This
data is included along with the ROM program and data file which is delivered when ordering a ROM
device. The SEC1=1:SEC0=0 state disengages security while the other three combinations engage
security.
In a similar manner the user can choose to allow or disallow a security unlocking mechanism through an
8-byte backdoor security key. There is no way to disable security unless the non-volatile
KEYEN1:KEYEN0 bits in NVOPT/ROPT are set to 1:0.
E.2.2
Provided that the key access is permitted, security can be disabled by the backdoor access sequence
described below:
The security key can be written only from a secure memory, so it cannot be entered through background
commands without the cooperation of a secure user program.
Freescale Semiconductor
1. Writing 1 to KEYACC in the RCNFG register. This causes the ROM control logic to interpret
2. Writing the correct four 16-bit key values to addresses NVBACKKEY through NVBACKKEY+7
3. Writing 0 to KEYACC in the RCNFG register. If the 8-byte key that was just written matches the
writes to the backdoor comparison key locations (NVBACKKEY through NVBACKKEY+7) as
values to be compared against the key rather than as writes to ROM locations.
locations. These writes must be done in order starting with the value for NVBACKKEY and ending
with NVBACKKEY+7. User software normally would get the key codes from outside the MCU
system through a communication interface such as a serial I/O.
key stored in the backdoor comparison key locations, SEC1:SEC0 in the ROPT register are
automatically changed to 10 and security will be disengaged until the next POR.
ROM Security
Security and Backdoor Key Access definition
Unsecuring the MCU using the Backdoor Key Access
The backdoor key is also used to protect access to internal product analysis
features. No product analysis will be possible on a secured ROM if
backdoor key access is disabled or keywords are invalid.
(ROPT)”.
MC9S12HZ256 Data Sheet, Rev. 2.05
NOTE
Appendix E ROM Description
Section E.1.1,
665