STM8S103F3P6

Manufacturer Part NumberSTM8S103F3P6
DescriptionMCU 8BIT 8KB FLASH 20-TSSOP
ManufacturerSTMicroelectronics
SeriesSTM8S
STM8S103F3P6 datasheet
 


Specifications of STM8S103F3P6

Core ProcessorSTM8Core Size8-Bit
Speed16MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsBrown-out Detect/Reset, POR, PWM, WDTNumber Of I /o16
Program Memory Size8KB (8K x 8)Program Memory TypeFLASH
Eeprom Size640 x 8Ram Size1K x 8
Voltage - Supply (vcc/vdd)2.95 V ~ 5.5 VData ConvertersA/D 5x10b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case20-TSSOPProcessor SeriesSTM8S10x
CoreSTM8Data Bus Width8 bit
Data Ram Size1 KBInterface TypeI2C, SPI, UART
Maximum Clock Frequency16 MHzNumber Of Programmable I/os16
Number Of Timers7Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWSTM8
Development Tools By SupplierSTM8/128-MCKIT, STM8S-DISCOVERY, ST-LINK, STICE-SYS001, STX-RLINKMinimum Operating Temperature- 40 C
On-chip Adc10 bit, 5 ChannelFeatured ProductSTM32 Cortex-M3 Companion Products
For Use With497-10593 - KIT STARTER FOR STM8S207/8 SERLead Free Status / RoHS StatusLead free / RoHS Compliant
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
Page 12/113

Download datasheet (2Mb)Embed
PrevNext
Product overview
SWIM
Single wire interface module for direct access to the debug module and memory programming.
The interface can be activated in all device operation modes. The maximum data transmission
speed is 145 bytes/ms.
Debug module
The non-intrusive debugging module features a performance close to a full-featured emulator.
Beside memory and peripherals, also CPU operation can be monitored in real-time by means
of shadow registers.
R/W to RAM and peripheral registers in real-time
R/W access to all resources by stalling the CPU
Breakpoints on all program-memory instructions (software breakpoints)
Two advanced breakpoints, 23 predefined configurations
4.3
Interrupt controller
Nested interrupts with three software priority levels
32 interrupt vectors with hardware priority
Up to 27 external interrupts on 6 vectors including TLI
Trap and reset interrupts
4.4
Flash program and data EEPROM memory
8 Kbytes of Flash program single voltage Flash memory
640 bytes true data EEPROM
User option byte area
Write protection (WP)
Write protection of Flash program memory and data EEPROM is provided to avoid unintentional
overwriting of memory that could result from a user software malfunction.
There are two levels of write protection. The first level is known as MASS (memory access
security system). MASS is always enabled and protects the main Flash program memory,
data EEPROM and option bytes.
To perform in-application programming (IAP), this write protection can be removed by writing
a MASS key sequence in a control register. This allows the application to write to data
EEPROM, modify the contents of main program memory or the device option bytes.
A second level of write protection, can be enabled to further protect a specific area of memory
known as UBC (user boot code). Refer to the figure below.
The size of the UBC is programmable through the UBC option byte, in increments of 1 page
(64-byte block) by programming the UBC option byte in ICP mode.
This divides the program memory into two areas:
Main program memory: Up to 8 Kbytes minus UBC
User-specific boot code (UBC): Configurable up to 8 Kbytes
The UBC area remains write-protected during in-application programming. This means that
the MASS keys do not unlock the UBC area. It protects the memory used to store the boot
12/113
STM8S103K3 STM8S103F3 STM8S103F2
DocID15441 Rev 6