STM8S103F3P6

Manufacturer Part NumberSTM8S103F3P6
DescriptionMCU 8BIT 8KB FLASH 20-TSSOP
ManufacturerSTMicroelectronics
SeriesSTM8S
STM8S103F3P6 datasheet
 


Specifications of STM8S103F3P6

Core ProcessorSTM8Core Size8-Bit
Speed16MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsBrown-out Detect/Reset, POR, PWM, WDTNumber Of I /o16
Program Memory Size8KB (8K x 8)Program Memory TypeFLASH
Eeprom Size640 x 8Ram Size1K x 8
Voltage - Supply (vcc/vdd)2.95 V ~ 5.5 VData ConvertersA/D 5x10b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case20-TSSOPProcessor SeriesSTM8S10x
CoreSTM8Data Bus Width8 bit
Data Ram Size1 KBInterface TypeI2C, SPI, UART
Maximum Clock Frequency16 MHzNumber Of Programmable I/os16
Number Of Timers7Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWSTM8
Development Tools By SupplierSTM8/128-MCKIT, STM8S-DISCOVERY, ST-LINK, STICE-SYS001, STX-RLINKMinimum Operating Temperature- 40 C
On-chip Adc10 bit, 5 ChannelFeatured ProductSTM32 Cortex-M3 Companion Products
For Use With497-10593 - KIT STARTER FOR STM8S207/8 SERLead Free Status / RoHS StatusLead free / RoHS Compliant
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
Page 15/113

Download datasheet (2Mb)Embed
PrevNext
STM8S103K3 STM8S103F3 STM8S103F2
Activation of the watchdog timers is controlled by option bytes or by software. Once activated,
the watchdogs cannot be disabled by the user program without performing a reset.
Window watchdog timer
The window watchdog is used to detect the occurrence of a software fault, usually generated
by external interferences or by unexpected logical conditions, which cause the application
program to abandon its normal sequence.
The window function can be used to trim the watchdog behavior to match the application
perfectly.
The application software must refresh the counter before time-out and during a limited time
window.
A reset is generated in two situations:
1. Timeout: At 16 MHz CPU clock the time-out period can be adjusted between 75 µs up to
64 ms.
2. Refresh out of window: The downcounter is refreshed before its value is lower than the
one stored in the window register.
Independent watchdog timer
The independent watchdog peripheral can be used to resolve processor malfunctions due to
hardware or software failures.
It is clocked by the 128 kHZ LSI internal RC clock source, and thus stays active even in case
of a CPU clock failure
The IWDG time base spans from 60 µs to 1 s.
4.8
Auto wakeup counter
Used for auto wakeup from active halt mode
Clock source: Internal 128 kHz internal low frequency RC oscillator or external clock
LSI clock can be internally connected to TIM1 input capture channel 1 for calibration
4.9
Beeper
The beeper function outputs a signal on the BEEP pin for sound generation. The signal is in
the range of 1, 2 or 4 kHz.
The beeper output port is only available through the alternate function remap option bit AFR7.
4.10
TIM1 - 16-bit advanced control timer
This is a high-end timer designed for a wide range of control applications. With its
complementary outputs, dead-time control and center-aligned PWM capability, the field of
applications is extended to motor control, lighting and half-bridge driver
16-bit up, down and up/down autoreload counter with 16-bit prescaler
Four independent capture/compare channels (CAPCOM) configurable as input capture,
output compare, PWM generation (edge and center aligned mode) and single pulse mode
output
Synchronization module to control the timer with external signals
DocID15441 Rev 6
Product overview
15/113