STM8S103F3P6

Manufacturer Part NumberSTM8S103F3P6
DescriptionMCU 8BIT 8KB FLASH 20-TSSOP
ManufacturerSTMicroelectronics
SeriesSTM8S
STM8S103F3P6 datasheet
 


Specifications of STM8S103F3P6

Core ProcessorSTM8Core Size8-Bit
Speed16MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsBrown-out Detect/Reset, POR, PWM, WDTNumber Of I /o16
Program Memory Size8KB (8K x 8)Program Memory TypeFLASH
Eeprom Size640 x 8Ram Size1K x 8
Voltage - Supply (vcc/vdd)2.95 V ~ 5.5 VData ConvertersA/D 5x10b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case20-TSSOPProcessor SeriesSTM8S10x
CoreSTM8Data Bus Width8 bit
Data Ram Size1 KBInterface TypeI2C, SPI, UART
Maximum Clock Frequency16 MHzNumber Of Programmable I/os16
Number Of Timers7Maximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWSTM8
Development Tools By SupplierSTM8/128-MCKIT, STM8S-DISCOVERY, ST-LINK, STICE-SYS001, STX-RLINKMinimum Operating Temperature- 40 C
On-chip Adc10 bit, 5 ChannelFeatured ProductSTM32 Cortex-M3 Companion Products
For Use With497-10593 - KIT STARTER FOR STM8S207/8 SERLead Free Status / RoHS StatusLead free / RoHS Compliant
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Page 41
42
Page 42
43
Page 43
44
Page 44
45
Page 45
46
Page 46
47
Page 47
48
Page 48
49
Page 49
50
Page 50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
Page 50/113

Download datasheet (2Mb)Embed
PrevNext
Electrical characteristics
Symbol
Ratings
I
VDD
Total current into V
I
Total current out of V
VSS
I
IO
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
(3) (4)
I
INJ(PIN)
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
(3)
ΣI
INJ(PIN)
Total injected current (sum of all I/O and control pins)
(1)
Data based on characterization results, not tested in production.
(2)
All power (V
) and ground (V
DD
(3)
I
must never be exceeded. This is implicitly insured if V
INJ(PIN)
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
>V
IN
pads, there is no positive injection current, and the corresponding V
(4)
ADC accuracy vs. negative injection current: Injecting negative current on any of the analog input pins
should be avoided as this significantly reduces the accuracy of the conversion being performed on
another analog input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins
which may potentially inject negative current. Any positive injection current within the limits specified for
I
and ΣI
in the I/O port pin characteristics section does not affect the ADC accuracy.
INJ(PIN)
INJ(PIN)
(5)
When several inputs are submitted to a current injection, the maximum ΣI
of the positive and negative injected currents (instantaneous values). These results are based on
characterization with ΣI
INJ(PIN)
Symbol
Ratings
T
Storage temperature range
STG
T
Maximum junction temperature
J
50/113
Table 17: Current characteristics
power lines (source)
DD
ground lines (sink)
SS
(5)
) pins must always be connected to the external supply.
SS
while a negative injection is induced by V
DD
maximum current injection on four I/O port pins of the device.
Table 18: Thermal characteristics
DocID15441 Rev 6
STM8S103K3 STM8S103F3 STM8S103F2
(1)
Max
(2)
100
(2)
80
20
- 20
± 4
± 4
± 4
(5)
± 20
maximum is respected. If V
IN
value. A positive
INJ(PIN)
<V
. For true open-drain
IN
SS
maximum must always be respected
IN
is the absolute sum
INJ(PIN)
Value
-65 to +150
150
Unit
mA
maximum
IN
Unit
°C