MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 212

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
SPRIE — SPI Receiver Interrupt Enable Bit
SPMSTR — SPI Master Bit
CPOL — Clock Polarity Bit
CPHA — Clock Phase Bit
SPWOM — SPI Wired-OR Mode Bit
SPE — SPI Enable
SPTIE— SPI Transmit Interrupt Enable
212
This read/write bit enables CPU interrupt requests generated by the SPRF bit. The SPRF bit is set
when a byte transfers from the shift register to the receive data register. Reset clears the SPRIE bit.
This read/write bit selects master mode operation or slave mode operation. Reset sets the SPMSTR
bit.
This read/write bit determines the logic state of the SPSCK pin between transmissions. (See
16-5
CPOL values. Reset clears the CPOL bit.
This read/write bit controls the timing relationship between the serial clock and SPI data. (See
16-5
CPHA values. When CPHA = 0, the SS pin of the slave SPI module must be set to 1 between bytes.
(See
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins
become open-drain outputs.
This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI. (See
Resetting the
This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte
transfers from the transmit data register to the shift register. Reset clears the SPTIE bit.
1 = SPRF CPU interrupt requests enabled
0 = SPRF CPU interrupt requests disabled
1 = Master mode
0 = Slave mode
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
1 = SPI module enabled
0 = SPI module disabled
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
and
and
Figure
Figure
Figure
Address: $0010
16-13.) Reset sets the CPHA bit.
Reset:
Read:
Write:
SPI.) Reset clears the SPE bit.
16-7.) To transmit data between SPI modules, the SPI modules must have identical
16-7.) To transmit data between SPI modules, the SPI modules must have identical
SPRIE
Bit 7
R
0
Figure 16-14. SPI Control Register (SPCR)
= Reserved
R
6
0
MC68HC908GR16 Data Sheet, Rev. 5.0
SPMSTR
5
1
CPOL
4
0
CPHA
3
1
= Unimplemented
SPWOM
2
0
SPE
1
0
Freescale Semiconductor
SPTIE
Bit 0
0
Figure
Figure
16.9