MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 219

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

As an example, a clock source of 4.9152 MHz, with the TMBCLKSEL set for divide-by-128 and the
TBR2–TBR0 set to {011}, the divider tap is1 and the interrupt rate calculates to:
17.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby modes.
17.6.1 Wait Mode
The timebase module remains active after execution of the WAIT instruction. In wait mode the timebase
register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power consumption by stopping
the timebase before executing the WAIT instruction.
17.6.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if the internal clock
generator has been enabled to operate during stop mode through the OSCENINSTOP bit in the
configuration register. The timebase module can be used in this mode to generate a periodic wakeup from
stop mode.
If the internal clock generator has not been enabled to operate in stop mode, the timebase module will
not be active during stop mode. In stop mode, the timebase register is not accessible by the CPU.
If the timebase functions are not required during stop mode, reduce power consumption by disabling the
timebase module before executing the STOP instruction.
Freescale Semiconductor
1/(4.9152 x 10
Do not change TBR2–TBR0 bits while the timebase is enabled (TBON = 1).
6
/128) = 26 μs
TBR2
0
0
0
0
1
1
1
1
Table 17-1. Timebase Divider Selection
MC68HC908GR16 Data Sheet, Rev. 5.0
TBR1
0
0
1
1
0
0
1
1
TBR0
0
1
0
1
0
1
0
1
NOTE
32,768
8192
2048
128
64
32
16
0
8
TMBCLKSEL
Divider Tap
4,194,304
1,048,576
262144
16,384
8192
4096
2048
1024
1
Low-Power Modes
219