MCF5307AI90B Freescale Semiconductor, MCF5307AI90B Datasheet - Page 331

• Manufacturer Part Number: MCF5307AI90B
• Description: IC MPU 32BIT COLDF 90MHZ 208FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF530xr

Specifications of MCF5307AI90B

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 90MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, POR, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 90 MHz
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 90MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: FQFP
• Program Memory Size: 8KB
• Cpu Speed: 90MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor, Inc.
Operation
14.5.2.1 Transmitting
The transmitter is enabled through the UART command register (UCRn). When it is ready
to accept a character, the UART sets USRn[TxRDY]. The transmitter converts parallel data
from the CPU to a serial bit stream on TxD. It automatically sends a start bit followed by
the programmed number of data bits, an optional parity bit, and the programmed number
of stop bits. The lsb is sent first. Data is shifted from the transmitter output on the falling
edge of the clock source.
After the stop bits are sent, if no new character is in the transmitter holding register, the TxD
output remains high (mark condition) and the transmitter empty bit, USRn[TxEMP], is set.
Transmission resumes and TxEMP is cleared when the CPU loads a new character into the
UART transmitter buffer (UTBn). If the transmitter receives a disable command, it
continues until any character in the transmitter shift register is completely sent.
If the transmitter is reset through a software command, operation stops immediately (see
Section 14.3.5, “UART Command Registers (UCRn)”). The transmitter is reenabled
through the UCRn to resume operation after a disable or software reset.
If the clear-to-send operation is enabled, CTS must be asserted for the character to be
transmitted. If CTS is negated in the middle of a transmission, the character in the shift
register is sent and TxD remains in mark state until CTS is reasserted. If the transmitter is
forced to send a continuous low condition by issuing a
command, the
SEND BREAK
transmitter ignores the state of CTS.
If the transmitter is programmed to automatically negate RTS when a message transmission
completes, RTS must be asserted manually before a message is sent. In applications in
which the transmitter is disabled after transmission is complete and RTS is appropriately
programmed, RTS is negated one bit time after the character in the shift register is
completely transmitted. The transmitter must be manually reenabled by reasserting RTS
before the next message is to be sent.
Figure 14-21 shows the functional timing information for the transmitter.
Chapter 14. UART Modules
14-21
For More Information On This Product,
Go to: www.freescale.com