CY7C68013A-128AXI Cypress Semiconductor Corp, CY7C68013A-128AXI Datasheet - Page 6

• Manufacturer Part Number: CY7C68013A-128AXI
• Description: IC MCU USB PERIPH HI SPD 128LQFP
• Manufacturer: Cypress Semiconductor Corp
• Series: EZ-USB FX2LP™r

Specifications of CY7C68013A-128AXI

• Program Memory Type: ROMless
• Package / Case: 128-LQFP
• Applications: USB Microcontroller
• Core Processor: 8051
• Controller Series: CY7C680xx
• Ram Size: 16K x 8
• Interface: I²C, USB, USART
• Number Of I /o: 40
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Processor Series: CY7C68xx
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, USART, USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 3
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: CY3684
• Minimum Operating Temperature: - 40 C
• Controller Family/series: (8051) USB
• Core Size: 8 Bit
• No. Of I/o's: 40
• Program Memory Size: 16KB
• Cpu Speed: 48MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, USART, USB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4611B - KIT USB TO ATA REFERENCE DESIGN428-1677 - KIT DEVELOPMENT EZ-USB FX2LP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-1943; CY7C68013A-128AXI

Table 4. Individual FIFO/GPIF Interrupt Sources
If Autovectoring is enabled (AV4EN = 1 in the INTSET-UP
register), the FX 2LP substitutes its INT4VEC byte. Therefore, if
the high byte (“page”) of a jump-table address is preloaded at
location 0x0054, the automatically inserted INT4VEC byte at
0x0055 directs the jump to the correct address out of the 14
addresses within the page. When the ISR occurs, the FX2LP
pushes the program counter to its stack then jumps to address
0x0053, where it expects to find a “jump” instruction to the ISR
Interrupt service routine.
3.9 Reset and Wakeup
3.9.1 Reset Pin
The input pin, RESET#, resets the FX2LP when asserted. This
pin has hysteresis and is active LOW. When a crystal is used with
the CY7C680xxA the reset period must enable stabilization of
the crystal and the PLL. This reset period must be approximately
Document #: 38-08032 Rev. *M
Note
3. If the external clock is powered at the same time as the CY7C680xxA and has a stabilization wait period, it must be added to the 200 μs.
Priority
10
11
12
13
14
1
2
3
4
5
6
7
8
9
INT4VEC Value
AC
8C
9C
80
88
90
94
98
A0
A4
A8
B0
B4
84
GPIFDONE
GPIFWF
Source
EP2PF
EP4PF
EP6PF
EP8PF
EP2EF
EP4EF
EP6EF
EP8EF
EP2FF
EP4FF
EP6FF
EP8FF
Endpoint 2 Programmable Flag
Endpoint 4 Programmable Flag
Endpoint 6 Programmable Flag
Endpoint 8 Programmable Flag
Endpoint 2 Empty Flag
Endpoint 4 Empty Flag
Endpoint 6 Empty Flag
Endpoint 8 Empty Flag
Endpoint 2 Full Flag
Endpoint 4 Full Flag
Endpoint 6 Full Flag
Endpoint 8 Full Flag
GPIF Operation Complete
GPIF Waveform
5 ms after VCC reaches 3.0V. If the crystal input pin is driven by
a clock signal the internal PLL stabilizes in 200 μs after VCC has
reached 3.0V.
Figure 2
applied during operation. A power on reset is defined as the time
reset that is asserted while power is being applied to the circuit.
A powered reset is when the FX2LP powered on and operating
and the RESET# pin is asserted.
Cypress provides an application note which describes and
recommends power on reset implementation. For more infor-
mation about reset implementation for the FX2 family of products
visit http://www.cypress.com.
on page 7 shows a power on reset condition and a reset
[3]
CY7C68013A, CY7C68014A
CY7C68015A, CY7C68016A
Notes
Page 6 of 62
[+] Feedback