LPC2361_62 NXP Semiconductors, LPC2361_62 Datasheet - Page 8

• Manufacturer Part Number: LPC2361_62
• Description: The LPC2361/2362 microcontrollers are based on a 16-bit/32-bit ARM7TDMI-S CPU with real-time emulation that combines the microcontroller with up to 128 kB of embedded high-speed flash memory
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC2361_62
Product data sheet
Symbol
P0[28]/SCL0
P0[29]/USB_D+
P0[30]/USB_D
P1[0] to P1[31]
P1[0]/ENET_TXD0
P1[1]/ENET_TXD1
P1[4]/ENET_TX_EN 93
P1[8]/ENET_CRS
P1[9]/ENET_RXD0
P1[10]/ENET_RXD1 90
P1[14]/
ENET_RX_ER
P1[15]/
ENET_REF_CLK
P1[16]/ENET_MDC
P1[17]/ENET_MDIO 86
P1[18]/
USB_UP_LED/
PWM1[1]/CAP1[0]
P1[19]/
USB_TX_E1/
USB_PPWR1/
CAP1[1]
Pin description
Pin
24
29
30
95
94
92
91
89
88
87
32
33
[4]
[5]
[5]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
…continued
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I/O
O
I/O
O
I/O
I
I/O
I
I/O
I
I/O
I
I/O
I
I/O
O
I/O
I/O
I/O
O
O
I
I/O
O
O
I
Description
P0[28] — General purpose digital input/output pin. Output is open-drain.
SCL0 — I
P0[29] — General purpose digital input/output pin.
USB_D+ — USB bidirectional D+ line.
P0[30] — General purpose digital input/output pin.
USB_D — USB bidirectional D line.
Port 1: Port 1 is a 32-bit I/O port with individual direction controls for each bit. The
operation of port 1 pins depends upon the pin function selected via the pin
connect block. Pins 2, 3, 5, 6, 7, 11, 12, and 13 of this port are not available.
P1[0] — General purpose digital input/output pin.
ENET_TXD0 — Ethernet transmit data 0 (LPC2362 only).
P1[1] — General purpose digital input/output pin.
ENET_TXD1 — Ethernet transmit data 1 (LPC2362 only).
P1[4] — General purpose digital input/output pin.
ENET_TX_EN — Ethernet transmit data enable (LPC2362 only).
P1[8] — General purpose digital input/output pin.
ENET_CRS — Ethernet carrier sense (LPC2362 only).
P1[9] — General purpose digital input/output pin.
ENET_RXD0 — Ethernet receive data (LPC2362 only).
P1[10] — General purpose digital input/output pin.
ENET_RXD1 — Ethernet receive data (LPC2362 only).
P1[14] — General purpose digital input/output pin.
ENET_RX_ER — Ethernet receive error (LPC2362 only).
P1[15] — General purpose digital input/output pin.
ENET_REF_CLK — Ethernet reference clock (LPC2362 only).
P1[16] — General purpose digital input/output pin.
ENET_MDC — Ethernet MIIM clock (LPC2362 only).
P1[17] — General purpose digital input/output pin.
ENET_MDIO — Ethernet MIIM data input and output (LPC2362 only).
P1[18] — General purpose digital input/output pin.
USB_UP_LED — USB GoodLink LED indicator. It is LOW when device is
configured (non-control endpoints enabled), or when host is enabled and has
detected a device on the bus. It is HIGH when the device is not configured, or
when host is enabled and has not detected a device on the bus, or during global
suspend. It transitions between LOW and HIGH (flashes) when host is enabled
and detects activity on the bus.
PWM1[1] — Pulse Width Modulator 1, channel 1 output.
CAP1[0] — Capture input for Timer 1, channel 0.
P1[19] — General purpose digital input/output pin.
USB_TX_E1 — Transmit Enable signal for USB port 1 (OTG transceiver).
USB_PPWR1 — Port Power enable signal for USB port 1.
CAP1[1] — Capture input for Timer 1, channel 1.
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 25 October 2011
2
C0 clock input/output. Open-drain output (for I
Single-chip 16-bit/32-bit MCU
LPC2361/62
2
C-bus compliance).
© NXP B.V. 2011. All rights reserved.
8 of 64