AT89C5132-ROTUL Atmel, AT89C5132-ROTUL Datasheet - Page 46

• Manufacturer Part Number: AT89C5132-ROTUL
• Description: IC 8051 MCU FLASH 64K USB 80TQFP
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5132-ROTUL

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: IDE/ATAPI, I²C, MMC, PCM, SPI, UART/USART, USB
• Peripherals: I²S, POR, WDT
• Number Of I /o: 44
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Cpu Family: 89C
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: IDE/SPI/UART/USB
• Total Internal Ram Size: 2.25KB
• # I/os (max): 44
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.3V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 2-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: TQFP
• Package: 80TQFP
• Family Name: 89C
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 44
• Number Of Timers: 2
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 2304 B
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 2
• Height: 1.45 mm
• Length: 14.1 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 2.7 V
• Width: 14.1 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.3
11.3.1
11.3.2
11.4
46
Idle Mode
Power-down Mode
AT89C5132
Entering Idle Mode
Exiting Idle Mode
Idle mode is a power reduction mode that reduces the power consumption. In this mode, pro-
gram execution halts. Idle mode freezes the clock to the CPU at known states while the
peripherals continue to be clocked (refer to Section “Oscillator”, page 12). The CPU status
before entering Idle mode is preserved, i.e., the program counter and program status word reg-
ister retain their data for the duration of Idle mode. The contents of the SFRs and RAM are also
retained. The status of the Port pins during Idle mode is detailed in
To enter Idle mode, the user must set the IDL bit in PCON register (see Table 18). The
AT89C5132 enters Idle mode upon execution of the instruction that sets IDL bit. The instruction
that sets IDL bit is the last instruction executed.
Note:
There are 2 ways to exit Idle mode:
1. Generate an enabled interrupt.
2. Generate a reset.
Note:
The Power-down mode places the AT89C5132 in a very low power state. Power-down mode
stops the oscillator and freezes all clocks at known states (refer to the Section "Oscillator",
page 12). The CPU status prior to entering Power-down mode is preserved, i.e., the program
counter, program status word register retain their data for the duration of Power-down mode. In
addition, the SFRs and RAM contents are preserved. The status of the Port pins during Power-
down mode is detailed in
Note:
–
–
If IDL bit and PD bit are set simultaneously, the AT89C5132 enter Power-down mode. Then it
does not go in Idle mode when exiting Power-down mode.
Hardware clears IDL bit in PCON register which restores the clock to the CPU.
Execution resumes with the interrupt service routine. Upon completion of the
interrupt service routine, program execution resumes with the instruction
immediately following the instruction that activated Idle mode. The general-purpose
flags (GF1 and GF0 in PCON register) may be used to indicate whether an interrupt
occurred during normal operation or during Idle mode. When Idle mode is exited by
an interrupt, the interrupt service routine may examine GF1 and GF0.
A logic high on the RST pin clears IDL bit in PCON register directly and
asynchronously. This restores the clock to the CPU. Program execution momentarily
resumes with the instruction immediately following the instruction that activated the
Idle mode and may continue for a number of clock cycles before the internal reset
algorithm takes control. Reset initializes the AT89C5132 and vectors the CPU to
address C:0000h.
During the time that execution resumes, the internal RAM cannot be accessed; however, it is pos-
sible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction
immediately following the instruction that activated Idle mode should not write to a Port pin or to
the external RAM.
V
tion. Notice, however, that V
DD
may be reduced to as low as V
Table
16.
DD
is not reduced until Power-down mode is invoked.
RET
during Power-down mode to further reduce power dissipa-
Table
16.
4173E–USB–09/07