R5F21258SNFP#U0 Renesas Electronics America, R5F21258SNFP#U0 Datasheet - Page 186

• Manufacturer Part Number: R5F21258SNFP#U0
• Description: IC R8C/25 MCU FLASH 52LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/25r

Specifications of R5F21258SNFP#U0

• Core Size: 16/32-Bit
• Program Memory Size: 64KB (64K x 8)
• Core Processor: R8C
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 52-LQFP
• No. Of I/o's: 41
• Ram Memory Size: 3KB
• Cpu Speed: 20MHz
• No. Of Timers: 4
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 2.2V To 5.5V
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: YMCRPR8C25 - REF PLATFORM MOTOR CTRL R8C/25R0K521256S000BE - KIT EVAL STARTER FOR R8C/25
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

R8C/24 Group, R8C/25 Group
Rev.3.00
REJ09B0244-0300
14.2.5
14.2.5.1
The following workaround should be performed in timer mode.
To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following
points:
• Timer RB stops counting after a reset. Set the values in the timer RB and timer RB prescalers before the
• Even if the prescaler and timer RB is read out in 16-bit units, these registers are read 1 byte at a time by the
• In programmable one-shot generation mode and programmable wait one-shot generation mode, when
• The TCSTF bit remains 0 (count stops) for 1 to 2 cycles of the count source after setting the TSTART bit to
• If the TSTOP bit in the TRBCR register is set to 1 during timer operation, timer RB stops immediately.
• If 1 is written to the TOSST or TOSSP bit in the TRBOCR register, the value of the TOSSTF bit changes
• When the TRBPRE register is written continuously, allow three or more cycles of the count source for each
• When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow
Feb 29, 2008
count starts.
MCU. Consequently, the timer value may be updated during the period when these two registers are being
read.
setting the TSTART bit in the TRBCR register to 0 (count stops) or setting the TOSSP bit in the TRBOCR
register to 1 (one-shot stops), the timer reloads the value of reload register and stops. Therefore, in
programmable one-shot generation mode and programmable wait one-shot generation mode, read the timer
count value before the timer stops.
1 (count starts) while the count is stopped.
During this time, do not access registers associated with timer RB
The TCSTF bit remains 1 for 1 to 2 cycles of the count source after setting the TSTART bit to 0 (count
stops) while the count is in progress. Timer RB counting is stopped when the TCSTF bit is set to 0.
During this time, do not access registers associated with timer RB
NOTE:
after one or two cycles of the count source have elapsed. If the TOSSP bit is written to 1 during the period
between when the TOSST bit is written to 1 and when the TOSSTF bit is set to 1, the TOSSTF bit may be
set to either 0 or 1 depending on the content state. Likewise, if the TOSST bit is written to 1 during the
period between when the TOSSP bit is written to 1 and when the TOSSTF bit is set to 0, the TOSSTF bit
may be set to either 0 or 1.
write interval.
for each write interval.
Notes on Timer RB
1. Registers associated with timer RB: TRBCR, TRBOCR, TRBIOC, TRBMR, TRBPRE, TRBSC, and
Timer mode
Page 167 of 485
TRBPR.
(1)
(1)
other than the TCSTF bit.
other than the TCSTF bit.
14. Timers