R5F21258SNFP#U0 Renesas Electronics America, R5F21258SNFP#U0 Datasheet - Page 89

• Manufacturer Part Number: R5F21258SNFP#U0
• Description: IC R8C/25 MCU FLASH 52LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/25r

Specifications of R5F21258SNFP#U0

• Core Size: 16/32-Bit
• Program Memory Size: 64KB (64K x 8)
• Core Processor: R8C
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 52-LQFP
• No. Of I/o's: 41
• Ram Memory Size: 3KB
• Cpu Speed: 20MHz
• No. Of Timers: 4
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 2.2V To 5.5V
• Embedded Interface Type: I2C, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: YMCRPR8C25 - REF PLATFORM MOTOR CTRL R8C/25R0K521256S000BE - KIT EVAL STARTER FOR R8C/25
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

R8C/24 Group, R8C/25 Group
Rev.3.00
REJ09B0244-0300
7.5
Figure 7.14
Table 7.48
NOTES:
Ports P0 to P2, P3_0,
P3_1, P3_3 to P3_7,
P4_3 to P4_5, P6
Ports P4_6, P4_7
Port P4_2, VREF
RESET
NC
Table 7.48 lists the Unassigned Pin Handling.
1. If these ports are set to output mode and left open, they remain in input mode until they are switched
2. Connect these unassigned pins to the MCU using the shortest wire length (2 cm or less) possible.
3. When the power-on reset function is in use.
to output mode by a program. The voltage level of these pins may be undefined and the power
current may increase while the ports remain in input mode.
The content of the direction registers may change due to noise or program runaway caused by
noise. In order to enhance program reliability, the program should periodically repeat the setting of
the direction registers.
Unassigned Pin Handling
Feb 29, 2008
(3)
Pin Name
Unassigned Pin Handling
Unassigned Pin Handling
Page 70 of 485
NOTE:
• After setting to input mode, connect each pin to VSS via a resistor (pull-
• After setting to output mode, leave these pins open.
Connect to VCC via a pull-up resistor
Connect to VCC
Connect to VCC via a pull-up resistor
Open or Connect to VCC and VSS
1. When the power-on reset function is in use.
down) or connect each pin to VCC via a resistor (pull-up).
P3_1, P3_3 to P3_7,
Port P0 to P2, P3_0,
P4_3 to P4_5, P6
MCU
Port P4_6, P4_7
Port P4_2/VREF
(Output mode)
(Input mode )
(Input mode)
RESET
:
:
(1)
Connection
Open
:
:
(2)
(2)
7. Programmable I/O Ports
(1,2)
(2)