MC68HC908JL8CSPE Freescale Semiconductor, MC68HC908JL8CSPE Datasheet - Page 148

• Manufacturer Part Number: MC68HC908JL8CSPE
• Description: IC MCU 8K FLASH 8MHZ 32-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JL8CSPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-SDIP (0.400", 10.16mm)
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Analog-to-Digital Converter (ADC)
10.5.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction. Any pending conversion is aborted.
ADC conversions resume when the MCU exits stop mode. Allow one conversion cycle to stabilize the
analog circuitry before attempting a new ADC conversion after exiting stop mode.
10.6 I/O Signals
The ADC module has 12 channels that are shared with I/O port B and port D, and one channel on
ADC12/T2CLK pin.
10.6.1 ADC Voltage In (ADCVIN)
ADCVIN is the input voltage signal from one of the 13 ADC channels to the ADC module.
10.7 I/O Registers
These I/O registers control and monitor ADC operation:
10.7.1 ADC Status and Control Register
The following paragraphs describe the function of the ADC status and control register.
COCO — Conversions Complete Bit
AIEN — ADC Interrupt Enable Bit
148
•
•
•
When the AIEN bit is a logic 0, the COCO is a read-only bit which is set each time a conversion is
completed. This bit is cleared whenever the ADC status and control register is written or whenever the
ADC data register is read. Reset clears this bit.
When the AIEN bit is a logic 1 (CPU interrupt enabled), the COCO is a read-only bit, and will always
be logic 0 when read.
When this bit is set, an interrupt is generated at the end of an ADC conversion. The interrupt signal is
cleared when the data register is read or the status/control register is written. Reset clears the AIEN bit.
1 = Conversion completed (AIEN = 0)
0 = Conversion not completed (AIEN = 0)
1 = ADC interrupt enabled
0 = ADC interrupt disabled
ADC status and control register (ADSCR)
ADC data register (ADR)
ADC clock register (ADICLK)
Address:
Reset:
Read:
Write:
MC68HC908JL8/JK8 • MC68HC08JL8/JK8 • MC68HC908KL8 Data Sheet, Rev. 3.1
Figure 10-3. ADC Status and Control Register (ADSCR)
$003C
COCO
Bit 7
0
AIEN
6
0
= Unimplemented
ADCO
5
0
ADCH4
4
1
ADCH3
3
1
ADCH2
2
1
ADCH1
1
1
Freescale Semiconductor
ADCH0
Bit 0
1