MC68HC908JL8CSPE Freescale Semiconductor, MC68HC908JL8CSPE Datasheet - Page 96

• Manufacturer Part Number: MC68HC908JL8CSPE
• Description: IC MCU 8K FLASH 8MHZ 32-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JL8CSPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-SDIP (0.400", 10.16mm)
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Monitor ROM (MON)
The control and data bytes are described below.
7.5.1 PRGRNGE
PRGRNGE is used to program a range of FLASH locations with data loaded into the data array.
The start location of the FLASH to be programmed is specified by the address ADDRH:ADDRL and the
number of bytes from this location is specified by DATASIZE. The maximum number of bytes that can be
programmed in one routine call is 128 bytes (max. DATASIZE is 128).
ADDRH:ADDRL do not need to be at a page boundary, the routine handles any boundary misalignment
during programming. A check to see that all bytes in the specified range are erased is not performed by
this routine prior programming. Nor does this routine do a verification after programming, so there is no
return confirmation that programming was successful. User must assure that the range specified is first
erased.
The coding example below is to program 32 bytes of data starting at FLASH location $EF00, with a bus
speed of 4.9152 MHz. The coding assumes the data block is already loaded in RAM, with the address
pointer, FILE_PTR, pointing to the first byte of the data block.
96
•
•
•
•
Bus speed — This one byte indicates the operating bus speed of the MCU. The value of this byte
should be equal to 4 times the bus speed, and should not be set to less than 4 (i.e. minimum bus
speed is 1MHz).
Data size — This one byte indicates the number of bytes in the data array that are to be
manipulated. The maximum data array size is 128. Routines EE_WRITE and EE_READ are
restricted to manipulate a data array between 2 to 15 bytes. Whereas routines ERARNGE and
MON_ERARNGE do not manipulate a data array, thus, this data size byte has no meaning.
Start address — These two bytes, high byte followed by low byte, indicate the start address of the
FLASH memory to be manipulated.
Data array — This data array contains data that are to be manipulated. Data in this array are
programmed to FLASH memory by the programming routines: PRGRNGE, MON_PRGRNGE,
EE_WRITE. For the read routines: LDRNGE, MON_LDRNGE, and EE_READ, data is read from
FLASH and stored in this array.
Routine Name
Routine Description
Calling Address
Stack Used
Data Block Format
MC68HC908JL8/JK8 • MC68HC08JL8/JK8 • MC68HC908KL8 Data Sheet, Rev. 3.1
Table 7-11. PRGRNGE Routine
PRGRNGE
Program a range of locations
$FC06
15 bytes
Bus speed (BUS_SPD)
Data size (DATASIZE)
Start address high (ADDRH)
Start address (ADDRL)
Data 1 (DATA1)
Data N (DATAN)
:
Freescale Semiconductor