MC9S08AW60CPUE Freescale Semiconductor, MC9S08AW60CPUE Datasheet - Page 146

• Manufacturer Part Number: MC9S08AW60CPUE
• Description: IC MCU 64K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AW60CPUE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08AW
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 8
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AW60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• For Use With: DEMO9S08AW60E - DEMO BOARD FOR MC9S08AW60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

1
2
3
Chapter 8 Internal Clock Generator (S08ICGV4)
8.4.10
A clock mode is requested by writing to CLKS1:CLKS0 and the actual clock mode is indicated by
CLKST1:CLKST0. Provided minimum conditions are met, the status shown in CLKST1:CLKST0 should
be the same as the requested mode in CLKS1:CLKS0.
CLKST, and ICGOUT. It also shows the conditions for CLKS = CLKST or the reason CLKS ≠ CLKST.
146
(CLKST)
CLKST will not update immediately after a write to CLKS. Several bus cycles are required before CLKST updates to the new
value.
The reference frequency has no effect on ICGOUT in SCM, but the reference frequency is still used in making the comparisons
that determine the DCOS bit
After initial LOCK; will be ICGDCLK/2R during initial locking process and while FLL is re-locking after the MFD bits are changed.
Actual
Mode
SCM
(XX)
FBE
FEE
(00)
(01)
(10)
(11)
FEI
Off
Clock Mode Requirements
Desired
(CLKS)
Mode
SCM
(XX)
FBE
FBE
FEE
FEE
FBE
FEE
FEE
(10)
(00)
(01)
(10)
(11)
(01)
(11)
(10)
(11)
(11)
FEI
FEI
Off
If a crystal will be used before the next reset, then be sure to set REFS = 1
and CLKS = 1x on the first write to the ICGC1 register. Failure to do so will
result in “locking” REFS = 0 which will prevent the oscillator amplifier
from being enabled until the next reset occurs.
Range
X
X
X
X
X
X
X
X
0
0
0
1
(f
f
f
f
f
ICGIRCLK
ICGIRCLK
ICGIRCLK
Frequency
Reference
f
f
ICGIRCLK
REFERENCE
ICGIRCLK
ICGIRCLK
f
f
ICGERCLK
ICGERCLK
0
0
0
0
MC9S08AW60 Data Sheet, Rev 2
/7
/7
/7
Table 8-9. ICG State Table
/7
/7
/7
(1)
(1)
(1)
2
)
128/f
Comparison
Cycle Time
2/f
8/f
8/f
8/f
8/f
8/f
8/f
NOTE
ICGERCLK
ICGIRCLK
ICGIRCLK
ICGIRCLK
ICGIRCLK
ICGIRCLK
ICGIRCLK
ICGERCLK
—
—
—
—
Table 8-9
ICGDCLK/R
ICGERCLK/R
ICGERCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGDCLK/R
ICGOUT
shows the relationship between CLKS,
0
0
(2)
3
Conditions
CLKS = CLKST
ERCS = 1 and
ERCS = 1 and
Not switching
from FBE to
DCOS = 1
ERCS = 1
DCOS = 1
DCOS = 1
SCM
—
—
—
—
—
—
—
Freescale Semiconductor
1
for
DCOS = 0 or
LOCS = 1 &
DCOS = 0
ERCS = 0
ERCS = 0
ERCS = 0
ERCS = 0
ERCS = 1
CLKS1 ≠
Reason
CLKST
—
—
—
—
—
—