MC9S08AW60CPUE Freescale Semiconductor, MC9S08AW60CPUE Datasheet - Page 149

• Manufacturer Part Number: MC9S08AW60CPUE
• Description: IC MCU 64K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AW60CPUE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08AW
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 8
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AW60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• For Use With: DEMO9S08AW60E - DEMO BOARD FOR MC9S08AW60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.5.2
In this example, the FLL will be used (in FEE mode) to multiply the external 32 kHz oscillator up to
8.38 MHz to achieve 4.19 MHz bus frequency.
After the MCU is released from reset, the ICG is in self-clocked mode (SCM) and supplies approximately
8 MHz on ICGOUT, which corresponds to a 4 MHz bus frequency (f
The clock scheme will be FLL engaged, external (FEE). So
Solving for N / R gives:
The values needed in each register to set up the desired operation are:
ICGC1 = $38 (%00111000)
ICGC2 = $00 (%00000000)
ICGS1 = $xx
ICGS2 = $xx
ICGFLTLU/L = $xx
Freescale Semiconductor
Bit 7
Bit 6
Bit 5
Bits 4:3 CLKS
Bit 2
Bit 1
Bit 0
Bit 7
Bits 6:4 MFD
Bit 3
Bits 2:0 RFD
This is read only except for clearing interrupt flag
This is read only; should read DCOS = 1 before performing any time critical tasks
Only needed in self-clocked mode; FLT will be adjusted by loop to give 8.38 MHz DCO clock
Bits 15:12 unused
101
110
111
Example #1: External Crystal = 32 kHz, Bus Frequency = 4.19 MHz
HGO
RANGE
REFS
OSCSTEN 0
LOCD
LOLRE
LOCRE
N / R = 8.38 MHz /(32 kHz * 64) = 4 ; we can choose N = 4 and R =1
0
0
1
11
0
0
0
000 Sets the MFD multiplication factor to 4
0
000 Sets the RFD division factor to ÷1
0000
f
ICGOUT
14
16
18
Configures oscillator for low power
Configures oscillator for low-frequency range; FLL prescale factor is 64
Oscillator using crystal or resonator is requested
FLL engaged, external reference clock mode
Oscillator disabled
Loss-of-clock detection enabled
Unimplemented or reserved, always reads zero
Generates an interrupt request on loss of lock
Generates an interrupt request on loss of clock
Table 8-12. MFD and RFD Decode Table
= f
ext
MC9S08AW60 Data Sheet, Rev 2
* P * N / R ; P = 64, f
ext
101
110
111
= 32 kHz
Chapter 8 Internal Clock Generator (S08ICGV4)
Bus
).
÷128
÷32
÷64
Eqn. 8-1
Eqn. 8-2
149