MC9S08AW60CPUE Freescale Semiconductor, MC9S08AW60CPUE Datasheet - Page 61

• Manufacturer Part Number: MC9S08AW60CPUE
• Description: IC MCU 64K FLASH 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AW60CPUE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08AW
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 8
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AW60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• For Use With: DEMO9S08AW60E - DEMO BOARD FOR MC9S08AW60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

1
4.6.4
During reset, the contents of the nonvolatile location NVPROT are copied from FLASH into FPROT. This
register may be read at any time.
4.6.5
Bits 3, 1, and 0 always read 0 and writes have no meaning or effect. The remaining five bits are status bits
that can be read at any time. Writes to these bits have special meanings that are discussed in the bit
descriptions.
Freescale Semiconductor
Background commands can be used to change the contents of these bits in FPROT.
FPS[7:1]
Reset
Reset
FPDIS
•
•
Field
7:1
0
W
W
R
R
If FPDIS = 0, then protection can be increased (in other words, a smaller value of FPS can be
written).
If FPDIS = 1, then writes do not change protection.
FCBEF
FLASH Protection Register (FPROT and NVPROT)
FLASH Status Register (FSTAT)
FPS7
FLASH Protect Select Bits — When FPDIS = 0, this 7-bit field determines the ending address of unprotected
FLASH locations at the high address end of the FLASH. Protected FLASH locations cannot be erased or
programmed.
FLASH Protection Disable
0 FLASH block specified by FPS[7:1] is block protected (program and erase not allowed).
1 No FLASH block is protected.
(1)
1
7
7
= Unimplemented or Reserved
FCCF
FPS6
(1)
1
6
6
This register is loaded from nonvolatile location NVPROT during reset.
Figure 4-9. FLASH Protection Register (FPROT)
Table 4-11. FPROT Register Field Descriptions
Figure 4-10. FLASH Status Register (FSTAT)
FPVIOL
FPS5
(1)
0
5
5
MC9S08AW60 Data Sheet, Rev 2
FACCERR
FPS4
(1)
0
4
4
Description
FPS3
(1)
3
3
0
0
FBLANK
FPS2
(1)
0
2
2
FPS1
(1)
0
0
1
1
Chapter 4 Memory
FPDIS
(1)
0
0
0
0
61