ATSAM3S4CA-AU Atmel, ATSAM3S4CA-AU Datasheet - Page 762

• Manufacturer Part Number: ATSAM3S4CA-AU
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 79
• Ram Memory Size: 48KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Cpu Family: AT91
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 64MHz
• Total Internal Ram Size: 48KB
• # I/os (max): 79
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.62V
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Figure 34-16. Input Stage
762
SAM3S Preliminary
TIOA0
TIOB0
TIOB1
INVA
INVB
By means of the MAXFILT field in TC_BMR, it is possible to configure a minimum duration for
which the pulse is stated as valid. When the filter is active, pulses with a duration lower than
MAXFILT+1 * tMCK ns are not passed to down-stream logic.
Filters can be disabled using the FILTER field in the TC_BMR register.
Input filtering can efficiently remove spurious pulses that might be generated by the presence of
particulate contamination on the optical or magnetic disk of the rotary sensor.
Spurious pulses can also occur in environments with high levels of electro-magnetic interfer-
ence. Or, simply if vibration occurs even when rotation is fully stopped and the shaft of the motor
is in such a position that the beginning of one of the reflective or magnetic bars on the rotary
sensor disk is aligned with the light or magnetic (Hall) receiver cell of the rotary sensor. Any
vibration can make the PHA, PHB signals toggle for a short duration.
INVIDX
1
1
1
SWAP
IDXPHB
1
PHA
PHB
Input Pre-Processing
IDX
MAXFILT
Filter
Filter
Filter
FILTER
1
1
1
Direction
and
Edge
Detection
PHedge
DIR
IDX
6500C–ATARM–8-Feb-11