UPSD3433E-40U6 STMicroelectronics, UPSD3433E-40U6 Datasheet - Page 125

• Manufacturer Part Number: UPSD3433E-40U6
• Description: MCU 8BIT 8032 128KB FLASH 80TQFP
• Manufacturer: STMicroelectronics
• Series: µPSDr

Specifications of UPSD3433E-40U6

• Core Processor: 8032
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• For Use With: 497-5518 - EVAL BOARD RFID READER497-5218 - KIT DEVELOPMENT FOR UPSD3400497-2381 - CABLE PROGRAMMER FLASH LINK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-4907

UPSD3422, UPSD3433, UPSD3434, UPSD3454
23.3
A few things to know related to these transfers:
●
●
●
●
●
●
●
●
Figure 41. Data transfer on an I
Operating modes
The I
●
●
●
●
Condition
Start
Either the Master or Slave device can hold the SCL clock line low to indicate it needs
more time to handle a byte transfer. An indefinite holding period is possible.
A Start condition is generated by a Master and recognized by a Slave when SDA has a
1-to-0 transition while SCL is high
A Stop condition is generated by a Master and recognized by a Slave when SDA has a
0-to1 transition while SCL is high
A Re-Start (repeated Start) condition generated by a Master can have the same
function as a Stop condition when starting another data transfer immediately following
the previous data transfer
When transferring data, the logic level on the SDA line must remain stable while SCL is
high, and SDA can change only while SCL is low. However, when not transferring data,
SDA may change state while SCL is high, which creates the Start and Stop bus
conditions.
An Acknowlegde bit is generated from a Master or a Slave by driving SDA low during
the “ninth” bit time, just following each 8-bit byte that is transfered on the bus
on page
bit time. All byte transfers on the I
Acknowlege (ACK) or Non-Acknowledge (NACK).
An additional Master device that desires to control the bus should wait until the bus is
not busy before generating a Start condition so that a possible Slave operation is not
interrupted.
If two Master devices both try to generate a Start condition simultaneously, the Master
who looses arbitration will switch immediately to Slave mode so it can recoginize its
own Slave address should it appear on the bus.
Master-transmitter
Master-receiver
Slave-transmitter
Slave-receiver
2
C interface supports four operating modes:
MSB
1
125). A Non-Acknowledge occurs when SDA is asserted high during the ninth
7-bit Slave
2
Address
3-6
Clock can be held low
to stall transfer.
7
READ/WRITE
(Figure 41 on page
Indicator
R/W
8
2
C bus
2
(Figure 41 on page
ACK
(Figure 41 on page
C bus include a 9th bit time reserved for an
9
MSB
Acknowledge
1
125).
bits from
receiver
Repeated if more
data bytes are
transferred.
2
125).
125).
3-8
ACK
9
NACK
I
2
C interface
(Figure 41
Stop
Condition
Repeated
Start
Condition
125/300
AI09625