UPSD3433E-40U6 STMicroelectronics, UPSD3433E-40U6 Datasheet - Page 206

• Manufacturer Part Number: UPSD3433E-40U6
• Description: MCU 8BIT 8032 128KB FLASH 80TQFP
• Manufacturer: STMicroelectronics
• Series: µPSDr

Specifications of UPSD3433E-40U6

• Core Processor: 8032
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• For Use With: 497-5518 - EVAL BOARD RFID READER497-5218 - KIT DEVELOPMENT FOR UPSD3400497-2381 - CABLE PROGRAMMER FLASH LINK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-4907

PSD module
206/300
Table 162. CSIOP registers and their offsets (in hexadecimal) (continued)
Drive Select
Input
Macrocells
Enable Out
Output
Macrocells
AB
(MCELLAB)
Output
Macrocells
BC
(MCELLBC)
Mask
Macrocells
AB
Mask
Macrocells
BC
Main Flash
Sector
Protection
Security Bit
and
Secondary
Flash
Sector
Protection
Register
name
(80-pin)
Port A
OCh
0Ah
08h
Port B Port C Port D Other
0Bh
0Dh
09h
16h
18h
1Ah
1Bh
17h
UPSD3422, UPSD3433, UPSD3434, UPSD3454
C0h
C2h
20h
21h
22h
23h
Write to configure port pins as
either CMOS push-pull or
Open Drain on some pins,
while selecting high slew rate
on other pins. Read to check
status. Default output type is
CMOS push-pull.
Read to obtain logic state of
IMCs. No WRITEs.
Read state of output enable
logic on each I/O port driver. 1
= driver output is enabled, 0 =
driver is off, and it is in high
impedance state. No WRITEs.
Read logic state of MCELLAB
outputs (bank of eight OMCs).
Write to load MCELLAB flip-
flops.
Read logic state of MCELLBC
outputs (bank of eight OMCs).
Write to load MCELLBC flip-
flops.
Write to set mask for
MCELLAB. Logic '1' blocks
READs/WRITEs of OMC. Logic
'0' will pass OMC value. Read
to check status.
Write to set mask for
MCELLBC. Logic '1' blocks
READs/WRITEs of OMC. Logic
'0' will pass OMC value. Read
to check status.
Read to determine Main Flash
Sector Protection Setting (non-
volatile) that was specified in
PSDsoft Express. No WRITEs.
Read to determine if PSD
module device Security Bit is
active (non-volatile) Logic 1 =
device secured. Also read to
determine Secondary Flash
Protection Setting (non-
volatile) that was specified in
PSDsoft. No WRITEs.
Description
Table 192
Table 173
Table 196
Table 169
Table 170
Table 171
Table 172
Table 165
Table 166
page 241
page 230
page 242
page 228
page 228
page 229
page 229
page 219
page 219
Link
on
on
on
on
on
on
on
on
on