UPSD3433E-40U6 STMicroelectronics, UPSD3433E-40U6 Datasheet - Page 262

• Manufacturer Part Number: UPSD3433E-40U6
• Description: MCU 8BIT 8032 128KB FLASH 80TQFP
• Manufacturer: STMicroelectronics
• Series: µPSDr

Specifications of UPSD3433E-40U6

• Core Processor: 8032
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• For Use With: 497-5518 - EVAL BOARD RFID READER497-5218 - KIT DEVELOPMENT FOR UPSD3400497-2381 - CABLE PROGRAMMER FLASH LINK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-4907

PSD module
28.6.7
262/300
Figure 93. Recommended JTAG connector
Chaining UPSD34xx devices
It is possible to chain a UPSD34xx device with other UPSD34xx devices on a circuit board,
and also chain with IEEE 1149.1 compliant devices from other manufacturers.
page 263
device, and so on. Only one device is performing JTAG operations at any given time while
the other two devices are in BYPASS mode. Configuration for JTAG chaining can be made in
PSDsoft Express by choosing “More than one device” when prompted about chaining
devices. Notice in
externally, but also be aware that the two die within each UPSD34xx device are chained
internally. This internal chaining of die is transparent to the user and is taken care of by
PSDsoft Express and 3rd party JTAG tool software.
The example in
devices. The signals TSTAT and TERR are configured as open-drain type signals from
PSDsoft Express. This facilitates a wired-OR connection of TSTAT signals from multiple
UPSD34xx devices and also a wired-OR connection of TERR signals from those same
multiple devices. PSDsoft Express puts TSTAT and TERR signals into open-drain mode by
default, requiring external pull-up resistors. Click on 'Properties' in the JTAG-ISP window of
PSDsoft Express to change to standard CMOS push-pull outputs if desired, but wired-OR
logic is not possible in CMOS output mode.
shows a chaining example. The TDO of one device connects to the TDI of the next
Figure 94 on page 263
Figure 94 on page 263
14
12
10
8
6
4
2
TERR
TSTAT
TRST
CNTL
GND
GND
RST
GND
TCK
TMS
V
JEN
TDO
TDI
CC
13
11
1
9
7
5
3
WAY
KEY
also shows how to use 6-pin JTAG when chaining
VIEW: Looking into face of shrouded
that the UPSD34xx devices are chained
UPSD3422, UPSD3433, UPSD3434, UPSD3454
male connector, with 0.025"
posts on 0.1" centers.
Connector reference:
Molex 70247-1401
This connector accepts a 14-pin
ribbon cable such as:
• Samtec:
• Digikey:
HCSD-07-D-06.00-01-S-N
M3CCK-14065-ND
AI09187
Figure 94 on