XCCACE-TQG144I Xilinx Inc, XCCACE-TQG144I Datasheet - Page 49

IC ACE CONTROLLER CHIP TQ144

XCCACE-TQG144I

Manufacturer Part Number
XCCACE-TQG144I
Description
IC ACE CONTROLLER CHIP TQ144
Manufacturer
Xilinx Inc
Datasheet

Specifications of XCCACE-TQG144I

Controller Type
ACE Controller
Voltage - Supply
3 V ~ 3.6 V
Current - Supply
30mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
144-TQFP, 144-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Interface
-
Other names
122-1511-5

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XCCACE-TQG144I
Manufacturer:
XILINX
Quantity:
100
Part Number:
XCCACE-TQG144I
Manufacturer:
XILINX
0
Part Number:
XCCACE-TQG144I
Manufacturer:
XILINX
Quantity:
1
Part Number:
XCCACE-TQG144I
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
Company:
Part Number:
XCCACE-TQG144I
Quantity:
1 500
Part Number:
XCCACE-TQG144ILEADFREE
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
Once the CompactFlash device is ready to receive a new
command, the following information needs to be written to
the MPU interface:
1. The sector address or logical block address (LBA) of
2. The number of sectors that will be written should be
3. The WriteMemCardData command (04h) should be
DS080 (v2.0) October 1, 2008
Product Specification
the first sector to be transferred should be written to the
following MPU address locations:
-
-
-
-
loaded into the low byte of the SECCNTCMDREG
register (MPU byte address 14h)
written to the high byte of the SECCNTCMDREG
register (MPU byte address 15h)
LBA[7:0] @ MPU byte address 10h
LBA[15:8] @ MPU byte address 11h
LBA[23:16] @ MPU byte address 12h
LBA[27:24] @ MPU byte address 13h (note that
only four bits are used in the most significant LBA
byte)
R
No
Wait for Buffer Ready
Write Data Buffer
Figure 29: Write Data Buffer Control Flow Process
Decrement Data
Buffer is written.
Return success.
Write data word
Count variable*
Count variable
Initialize Data
Data Count
equal to 0?
to buffer
Yes
www.xilinx.com
*Set Data Count variable equal to
the number of data items in a buffer
(e.g., 16 bytes or 32 words)
Write data bits 7:0 to byte address 40h
Write data bits 15:8 to byte address 41h
(Note that the following conditions must
be valid for a data write to occur to the
CompactFlash data buffer:
1. The data buffer must be ready
2. A single write to byte address 41h
must occur that will cause the entire 16-
bit data register to be written to the
buffer)
4. Reset the CFGJTAG controller by setting the
Immediately after writing the command to the MPU inter-
face, the CFGJTAG controller should be reset before writing
the sector data to the data buffer.
The control flow process for writing the sector data from the
data buffer is shown in
After all of the required sector data has been written, the
CFGJTAG controller should be taken out of reset and the
CompactFlash lock should be released. This is done by set-
ting the CFGRESET (bit 7) and LOCKREQ (bit 1) bits of the
low byte of the CONTROLREG register (MPU byte address
18h) to a 0, respectively. Note that all requested sector data
should be written to the data buffer in order to avoid a dead-
lock situation with the CompactFlash device.
CFGRESET bit (bit 7) of the CONTROLREG register
(MPU address 18h) to a 1.
System ACE CompactFlash Solution
DS080_54_051701
Figure
29.
49

Related parts for XCCACE-TQG144I