XCB56362PV100 Freescale Semiconductor, XCB56362PV100 Datasheet - Page 29

• Manufacturer Part Number: XCB56362PV100
• Description: DSP Floating-Point 24-Bit 100MHz 100MIPS 144-Pin LQFP
• Manufacturer: Freescale Semiconductor

Specifications of XCB56362PV100

• Package: 144LQFP
• Numeric And Arithmetic Format: Floating-Point
• Maximum Speed: 100 MHz
• Ram Size: 33 KB
• Device Million Instructions Per Second: 100 MIPS

1
2
3
4
5
6
7
3.5
The timing waveforms shown in the AC electrical characteristics section are tested with a V
of 0.3 V and a V
shown in Note 6 of the previous table. AC timing specifications, which are referenced to a device input
signal, are measured in production with respect to the 50% point of the respective input signal's transition.
DSP56362 output levels are measured with the production test machine V
at 0.4 V and 2.4 V, respectively.
Freescale Semiconductor
Input leakage current
High impedance (off-state) input current (@ 2.4 V / 0.4 V)
Output high voltage
Output low voltage
Internal supply current
for current measurements)
PLL supply current
Input capacitance
• TTL (I
• CMOS (I
• TTL (I
• CMOS (I
• In Normal mode
• In Wait mode
• In Stop mode
V
Refers to MODA/IRQA, MODB/IRQB, MODC/IRQC, and MODD/IRQD pins.
Driving EXTAL to the low V
minimize power consumption, the minimum V
than 0.1 V
Periodically sampled and not 100% tested.
This characteristic does not apply to PCAP.
Section 5.3, "Power Consumption Considerations"
requirements in Normal mode. In order to obtain these results, all inputs must be terminated (i.e., not allowed to float).
Measurements are based on synthetic intensive DSP benchmarks. The power consumption numbers in this specification are
90% of the measured results of this benchmark. This reflects typical DSP applications. Typical internal supply current is
measured with V
In order to obtain these results, all inputs, which are not disconnected at Stop mode, must be terminated (i.e., not allowed to
float).
CC
= 3.3 V ± 5% V; T
OH
OL
AC Electrical Characteristics
OH
OL
= 3.0 µA, open-drain pins I
= –0.4 µA)
CC
= 10 µA)
.
= –10 µA)
7
Although the minimum value for the frequency of EXTAL is 0 MHz, the
device AC test conditions are 15 MHz and rated speed.
4
CC
IH
Characteristics
= 3.3 V at T
6
4, 5
minimum of 2.4 V for all pins except EXTAL, which is tested using the input levels
4
(Operating frequency 100MHz
J
4
= 0°C to +100°C, C
IHX
Table 3-3 DC Electrical Characteristics
or the high V
J
= 100°C. Maximum internal supply current is measured with V
OL
= 6.7 µA)
L
ILX
DSP56362 Technical Data, Rev. 4
= 50 pF
IHX
value may cause additional power consumption (DC current). To
should be no lower than 0.9 V
4, 5
NOTE
Symbol
I
I
V
V
I
CCW
I
C
CCS
CCI
I
TSI
IN
OH
OL
IN
provides a formula to compute the estimated current
V
CC
Min
–10
–10
2.4
—
—
—
—
—
—
– 0.01
1
CC
(continued)
and the maximum V
OL
Typ
127
7. 5
100
and V
—
—
—
—
—
—
1
AC Electrical Characteristics
CC
OH
= 3.46 V at T
reference levels set
ILX
should be no higher
Max
0.01
181
150
0.4
2.5
10
10
11
10
—
IL
J
maximum
= 100°C.
Unit
µA
µA
µA
µA
pF
V
V
3-3