ATmega1280 Atmel Corporation, ATmega1280 Datasheet - Page 85

• Manufacturer Part Number: ATmega1280
• Manufacturer: Atmel Corporation

Specifications of ATmega1280

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 86
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 1
• Uart: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 16
• Input Capture Channels: 4
• Pwm Channels: 15
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

2549N–AVR–05/11
Table 13-13. Overriding Signals for Alternate Functions PD7:PD4
Table 13-14. Overriding Signals for Alternate Functions in PD3:PD0
Note:
Signal Name
Signal Name
DIEOE
DIEOV
DDOE
PUOE
PUOV
DDOV
PVOE
PVOV
DIEOE
DIEOV
DDOE
PUOE
PUOV
DDOV
PVOE
PVOV
AIO
AIO
DI
DI
1. When enabled, the 2-wire Serial Interface enables Slew-Rate controls on the output pins PD0
and PD1. This is not shown in this table. In addition, spike filters are connected between the
AIO outputs shown in the port figure and the digital logic of the TWI module.
PD3/INT3/TXD1
INT3 ENABLE
INT3 INPUT
T0 INPUT
PD7/T0
TXEN1
TXEN1
TXEN1
TXD1
0
0
0
0
0
0
0
0
–
0
1
–
1
ATmega640/1280/1281/2560/2561
T1 INPUT
PD6/T1
INT2 INPUT/RXD1
PD2/INT2/RXD1
PORTD2 • PUD
INT2 ENABLE
0
0
0
0
0
0
0
0
–
RXEN1
RXEN1
0
0
0
1
–
XCK1 OUTPUT ENABLE
XCK1 OUTPUT ENABLE
XCK1 OUTPUT
XCK1 INPUT
PD5/XCK1
PORTD1 • PUD
PD1/INT1/SDA
INT1 ENABLE
INT1 INPUT
SDA INPUT
SDA_OUT
0
0
1
0
0
–
TWEN
TWEN
TWEN
0
1
(1)
PORTD0 • PUD
PD0/INT0/SCL
INT0 ENABLE
INT0 INPUT
SCL INPUT
SCL_OUT
ICP1 INPUT
TWEN
TWEN
TWEN
PD4/ICP1
0
1
0
0
0
0
0
0
0
0
–
85