SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 404

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

Figure 33-6. Master Write with One Data Byte
Figure 33-7. Master Write with Multiple Data Byte
Figure 33-8. Master Write with One Byte Internal Address and Multiple Data Bytes
33.7.5
404
TXCOMP
TXCOMP
TXRDY
TXRDY
TWD
TWD
Write THR (Data n)
AT91SAM9R64/RL64
Master Receiver Mode
S
Write THR (Data n)
S
DADR
TXCOMP
DADR
TXRDY
TWD
TXRDY is used as Transmit Ready for the PDC transmit channel.
The read sequence begins by setting the START bit. After the start condition has been sent, the
master sends a 7-bit slave address to notify the slave device. The bit following the slave address
indicates the transfer direction, 1 in this case (MREAD = 1 in TWI_MMR). During the acknowl-
edge clock pulse (9th pulse), the master releases the data line (HIGH), enabling the slave to pull
it down in order to generate the acknowledge. The master polls the data line during this clock
pulse and sets the NACK bit in the status register if the slave does not acknowledge the byte.
If an acknowledge is received, the master is then ready to receive data from the slave. After data
has been received, the master sends an acknowledge condition to notify the slave that the data
has been received except for the last data, after the stop condition. See
W
Write THR (DATA)
S
W
A
DADR
IADR(7:0)
A
Write THR (Data n+1)
DATA n
W
A
A
DATA n
Write THR (Data n+1)
A
DATA
A
Write THR (Data n+x)
DATA n+5
Last data sent
(ACK received and TXRDY = 1)
A
STOP sent automaticaly
Write THR (Data n+x)
DATA n+5
Last data sent
P
A
A
DATA n+x
(ACK received and TXRDY = 1)
(ACK received and TXRDY = 1)
STOP sent automaticaly
DATA n+x
STOP sent automaticaly
Figure
6289D–ATARM–3-Oct-11
A
33-9. When the
A
P
P