SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 803

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.5.27
Name:
Access Type:
• CHANN_ENB: Channel Enable Status
0 = if cleared, the DMA channel no longer transfers data, and may load the next descriptor if the UDPHS_DMACONTROLx
register LDNXT_DSC bit is set.
When any transfer is ended either due to an elapsed byte count or a UDPHS device initiated transfer end, this bit is auto-
matically reset.
1 = if set, the DMA channel is currently enabled and transfers data upon request.
This bit is normally set or cleared by writing into the UDPHS_DMACONTROLx register CHANN_ENB bit field either by soft-
ware or descriptor loading.
If a channel request is currently serviced when the UDPHS_DMACONTROLx register CHANN_ENB bit is cleared, the
DMA FIFO buffer is drained until it is empty, then this status bit is cleared.
• CHANN_ACT: Channel Active Status
0 = the DMA channel is no longer trying to source the packet data.
When a packet transfer is ended this bit is automatically reset.
1 = the DMA channel is currently trying to source packet data, i.e. selected as the highest-priority requesting channel.
When a packet transfer cannot be completed due to an END_BF_ST, this flag stays set during the next channel descriptor
load (if any) and potentially until UDPHS packet transfer completion, if allowed by the new descriptor.
• END_TR_ST: End of Channel Transfer Status
0 = cleared automatically when read by software.
1 = set by hardware when the last packet transfer is complete, if the UDPHS device has ended the transfer.
Valid until the CHANN_ENB flag is cleared at the end of the next buffer transfer.
• END_BF_ST: End of Channel Buffer Status
0 = cleared automatically when read by software.
1 = set by hardware when the BUFF_COUNT downcount reach zero.
Valid until the CHANN_ENB flag is cleared at the end of the next buffer transfer.
6289D–ATARM–3-Oct-11
31
23
15
–
7
–
UDPHS DMA Channel Status Register
DESC_LDST
30
22
14
Read/Write
–
6
UDPHS_DMASTATUSx [x = 1..5]
END_BF_ST
29
21
13
–
5
END_TR_ST
28
20
12
–
4
BUFF_COUNT
BUFF_COUNT
27
19
11
–
–
3
AT91SAM9R64/RL64
26
18
10
–
2
–
CHANN_ACT
25
17
9
–
1
CHANN_ENB
24
16
8
–
0
803