SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 683

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.11.8
Name: DMACON
Access: Read/Write
Reset value: 0x00000000
• DMAEN: DMA Enable
0: DMA is disabled.
1: DMA is enabled.
• DMARST: DMA Reset (Write-only)
0: No effect.
1: Reset DMA module. DMA Module should be reset only when disabled and in idle state.
• DMABUSY: DMA Busy
0: DMA module is idle.
1: DMA module is busy (doing a transaction on the AHB bus).
• DMAUPDT: DMA Configuration Update
0: No effect
1: Update DMA Configuration
addressing. The values written in the registers DMABADDR1, DMABADDR2 and DMA2DCFG, and in the field FRMSIZE of
register DMAFRMCFG, are accepted by the DMA controller and are applied at the next frame. This bit is used only if a dual
scan configuration is selected (bit SCANMOD of LCDCON2 register) or 2D addressing is enabled (bit DMA2DEN in this
register). Otherwise, the LCD controller accepts immediately the values written in the registers referred to above.
• DMA2DEN: DMA 2D Addressing Enable
0: 2D addressing is disabled (values in register DMA2DCFG are “don’t care”).
1: 2D addressing is enabled.
6289D–ATARM–3-Oct-11
31
23
15
–
–
–
7
–
DMA Control Register
30
22
14
–
–
–
6
–
.
Used for simultaneous updating of DMA parameters in dual scan mode or when using 2D
29
21
13
–
–
–
5
–
DMA2DEN
28
20
12
–
–
–
4
DMAUPDT
27
19
11
–
–
–
3
DMABUSY
AT91SAM9R64/RL64
26
18
10
–
–
–
2
DMARST
25
17
–
–
9
–
1
DMAEN
24
16
–
–
8
–
0
683