SAM9RL64 Atmel Corporation, SAM9RL64 Datasheet - Page 891

• Manufacturer Part Number: SAM9RL64
• Manufacturer: Atmel Corporation

Specifications of SAM9RL64

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 240 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 118
• Ext Interrupts: 118
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 5
• Ssc: 2
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 220
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

6289D–ATARM–3-Oct-11
Doc. Rev.
6289B
Doc. Rev.
6289A
Comments (Continued)
PMC:
Section 27.8.10 “PMC Clock Generator PLL
“Bit 29 must always be set to 1 when programming CKGR_PLLR register.
TSADCC:
Section 43.4.1 “Power
UDPHS:
Figure 41-2 “Board
Table 41-1, “UDPHS Endpoint
“USB High Speed Device Port (UDPHS) User
Table 41-5, “Register Mapping”
Section 41.5.7 “UDPHS Test SOF Counter Register”
Section 41.5.8 “UDPHS Test A Counter Register”
Section 41.5.9 “UDPHS Test B Counter Register”
Section 41.5.10 “UDPHS Test Mode Register”
Electrical Characteristics:
Table 44-1, “Absolute Maximum
Table 44-2, “DC
V
Table 44-19, “Transfer
Section 44.6
Figure 44-8 “SPI Slave Mode - NPCS
Section 44.8
Table 44-22, “Processor Clock Waveform
Table 44-40, “MCI Timings High
Table 44-3, “Power Consumption for Different
Section 44.7 “Power Supply
Mechanical Characteristics:
Table 45-1
ERRATA:
Section 47.2.11
OL
Comments
First Issue
and V
OH
and
rows updated with new conditions
“ADC”, section upgraded one level in chapter organization.
“Timings”, except in formulas, negative values replaced by 0 in timing tables.
Table 45-5
“TSADCC”, added to errata.
Characteristics”, I
Schematic”, updated.
Management”, updated.
Characteristics”, Gain Error row updated.
Soldering Information is for Substrate Level.
Characteristics”, section updated.
Description”, High Bandwidth column updated.
Ratings”, updated industrial operating temperature.
Speed”, added to datasheet.
SC
rows updated.
Timings”, illustration replaced.
Parameters”, STH corner, MAX updated
Register”, inserted a 1 into bit field 29 and warning:
Interface”, internal test registers added.
Modes”,Active mode updated.
AT91SAM9R64/RL64
Change
Request
Ref.
5602
5853
5856
5711/5281
5688
5555
5277
5289
5278
5525
5613
5614
5622
5708
5803
rfo
5744
5549
Change
Request
Ref.
891