PIC18F2480 MICROCHIP [Microchip Technology], PIC18F2480 Datasheet - Page 175

• Manufacturer Part Number: PIC18F2480
• Description: 28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
• Manufacturer: MICROCHIP [Microchip Technology]

16.0
In PIC18F4480/4580 devices, ECCP1 is implemented
as a standard CCP module with Enhanced PWM
capabilities. These include the provision for 2 or 4
output channels, user selectable polarity, dead-band
control and automatic shutdown and restart. The
REGISTER 16-1:
 2004 Microchip Technology Inc.
Note:
ENHANCED
CAPTURE/COMPARE/PWM
(ECCP) MODULE
The ECCP1 module is implemented only
in PIC18F4X80 (40/44-pin) devices.
bit 7-6
bit 5-4
bit 3-0
ECCP1CON REGISTER (ECCP1 MODULE, PIC18F4480/4580 DEVICES)
bit 7
EPWM1M1:EPWM1M0: Enhanced PWM Output Configuration bits
If ECCP1M3:ECCP1M2 = 00, 01, 10:
xx = P1A assigned as Capture/Compare input/output; P1B, P1C, P1D assigned as port pins
If ECCP1M3:ECCP1M2 = 11:
00 = Single output: P1A modulated, P1B, P1C, P1D assigned as port pins
01 = Full-bridge output forward: P1D modulated; P1A active; P1B, P1C inactive
10 = Half-bridge output: P1A, P1B modulated with dead-band control; P1C, P1D assigned
11 = Full-bridge output reverse: P1B modulated; P1C active; P1A, P1D inactive
EDC1B1:EDC1B0: Enhanced PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found
in CCPRxL.
ECCP1M3:ECCP1M0: Enhanced CCP Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCP module)
0001 = Reserved
0010 = Compare mode, toggle output on match
0011 = Reserved
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, initialize ECCP pin low, set output on compare match (set ECCP1IF)
1001 = Compare mode, initialize ECCP pin high, clear output on compare match (set ECCP1IF)
1010 = Compare mode, generate software interrupt only, CCP pin reverts to I/O state
1011 = Compare mode, trigger special event (ECCP resets TMR1 or TMR3, sets ECCP1IF bit and
1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high
1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low
1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high
1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low
Legend:
R = Readable bit
-n = Value at POR
EPWM1M1 EPWM1M0
R/W-0
as port pins
starts the A/D conversion on ECCP1 match)
R/W-0
PIC18F2480/2580/4480/4580
EDC1B1
W = Writable bit
‘1’ = Bit is set
R/W-0
Preliminary
EDC1B0
R/W-0
Enhanced features are discussed in detail in
Section 16.4 “Enhanced PWM Mode”. Capture,
Compare and single-output PWM functions of the
ECCP module are the same as described for the
standard CCP module.
The control register for the Enhanced CCP module is
shown in Register 16-1. It differs from the CCP1CON
register in PIC18F2480/2580 devices in that the two
Most Significant bits are implemented to control PWM
functionality.
ECCP1M3 ECCP1M2 ECCP1M1
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
R/W-0
x = Bit is unknown
R/W-0
DS39637A-page 173
ECCP1M0
R/W-0
bit 0