XE8000EV108 Semtech, XE8000EV108 Datasheet - Page 88
XE8000EV108
Manufacturer Part Number
XE8000EV108
Description
EVAL BOARD FOR XE8806/XE8807
Manufacturer
Semtech
Type
MCUr
Specifications of XE8000EV108
Contents
Fully Assembled Evaluation Board
For Use With/related Products
XE88LC06AMI026
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 88 of 143
- Download datasheet (889Kb)
14.8.2.1
In this case, the interface will not look for a start sequence. The incoming data stream will be decoded according to
the selected PCM code and will be stored in the reception FIFO as soon as the reception mode is enabled. The
message start has to be detected by software.
14.8.2.2
The NRZ coding has no defined start sequence. Selecting the “protocol” start sequence in NRZ has the same
effect as no start detection.
In the bi-phase or Manchester code, any protocol violation is considered as a start sequence i.e. a 1-level or 0-level
which is longer than the duration of a chip. An example is shown in Figure 14-3.
In the delay modulation or Miller coding, any protocol violation is considered as a start sequence i.e. a 1-level or 0-
level which is longer than the duration of 2 chips.
Figure 14-3 : Start sequence type in Bi-Phase-Level encoding
14.8.2.3
An external start detection signal can be used. This signal should be connected to the pin RFIF2. The falling edge
of RFIF2 (also called “match”, see Figure 14-1) indicates the first valid bit of the message. This edge has to occur
during the first half of the first bit as shown in Figure 14-4. The minimal width of the pulse is half a bit.
© Semtech 2006
Bi-Phase - Level
“Protocol” start detection
“External” start detection
No start sequence detection
codes
1
bit sequence
1
Table 14-13. Start detection mode selection
0
1
“pattern 8bits”
1
“protocol”
“external”
0
“None”
name
start detection mode
0
0
1
start sequence
1
14-8
5 x '1'
RfifEnStart[1:0]
1
1
00
01
10
11
first valid bit
1
0
0
1
0
sequence
3 x '0'
other
start
0
XE8806A/XE8807A
0
first valid bit
1
1
0
www.semtech.com
Related parts for XE8000EV108
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: