MCU ARM 64KB FLASH/TIMER 100LQFP

STM32F101V8T6

Manufacturer Part NumberSTM32F101V8T6
DescriptionMCU ARM 64KB FLASH/TIMER 100LQFP
ManufacturerSTMicroelectronics
SeriesSTM32
STM32F101V8T6 datasheet
 


Specifications of STM32F101V8T6

Core ProcessorARM® Cortex-M3™Core Size32-Bit
Speed36MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsDMA, PDR, POR, PVD, PWM, Temp Sensor, WDTNumber Of I /o80
Program Memory Size64KB (64K x 8)Program Memory TypeFLASH
Ram Size10K x 8Voltage - Supply (vcc/vdd)2 V ~ 3.6 V
Data ConvertersA/D 16x12bOscillator TypeInternal
Operating Temperature-40°C ~ 85°CPackage / Case100-LQFP
Processor SeriesSTM32F101xCoreARM Cortex M3
Data Bus Width32 bitData Ram Size10 KB
Interface TypeI2C, SPI, USARTMaximum Clock Frequency36 MHz
Number Of Programmable I/os100Number Of Timers3 x 16 bit
Operating Supply Voltage2 V to 3.6 VMaximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
Minimum Operating Temperature- 40 COn-chip Adc12 bit, 16 Channel
For Use With497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCULead Free Status / RoHS StatusLead free / RoHS Compliant
Eeprom Size-Other names497-6060
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
Page 29/87

Download datasheet (2Mb)Embed
PrevNext
STM32F101x8, STM32F101xB
5
Electrical characteristics
5.1
Parameter conditions
Unless otherwise specified, all voltages are referenced to V
5.1.1
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at T
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on
characterization, the minimum and maximum values refer to sample tests and represent the
mean value plus or minus three times the standard deviation (mean±3Σ).
5.1.2
Typical values
Unless otherwise specified, typical data are based on T
2 V ≤ V
≤ 3.6 V voltage range). They are given only as design guidelines and are not
DD
tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean±2Σ)
5.1.3
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
5.1.4
Loading capacitor
The loading conditions used for pin parameter measurement are shown in
5.1.5
Pin input voltage
The input voltage measurement on a pin of the device is described in
SS
= 25 °C and T
A
= 25 °C, V
A
.
Doc ID 13586 Rev 14
Electrical characteristics
.
= T
max (given by
A
A
= 3.3 V (for the
DD
Figure
9.
Figure
10.
29/87