MCU ARM 64KB FLASH/TIMER 100LQFP

STM32F101V8T6

Manufacturer Part NumberSTM32F101V8T6
DescriptionMCU ARM 64KB FLASH/TIMER 100LQFP
ManufacturerSTMicroelectronics
SeriesSTM32
STM32F101V8T6 datasheet
 


Specifications of STM32F101V8T6

Core ProcessorARM® Cortex-M3™Core Size32-Bit
Speed36MHzConnectivityI²C, IrDA, LIN, SPI, UART/USART
PeripheralsDMA, PDR, POR, PVD, PWM, Temp Sensor, WDTNumber Of I /o80
Program Memory Size64KB (64K x 8)Program Memory TypeFLASH
Ram Size10K x 8Voltage - Supply (vcc/vdd)2 V ~ 3.6 V
Data ConvertersA/D 16x12bOscillator TypeInternal
Operating Temperature-40°C ~ 85°CPackage / Case100-LQFP
Processor SeriesSTM32F101xCoreARM Cortex M3
Data Bus Width32 bitData Ram Size10 KB
Interface TypeI2C, SPI, USARTMaximum Clock Frequency36 MHz
Number Of Programmable I/os100Number Of Timers3 x 16 bit
Operating Supply Voltage2 V to 3.6 VMaximum Operating Temperature+ 85 C
Mounting StyleSMD/SMT3rd Party Development ToolsEWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
Minimum Operating Temperature- 40 COn-chip Adc12 bit, 16 Channel
For Use With497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCULead Free Status / RoHS StatusLead free / RoHS Compliant
Eeprom Size-Other names497-6060
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
Page 81
82
Page 82
83
Page 83
84
Page 84
85
Page 85
86
Page 86
87
Page 87
Page 81/87

Download datasheet (2Mb)Embed
PrevNext
STM32F101x8, STM32F101xB
Table 54.
Document revision history (continued)
Date
Revision
18-Oct-2007
V
value added to
ESD(CDM)
Note added below
Table 10: Embedded reset and power control block
characteristics. and below
characteristics.
Note added below
Table 35: Output voltage characteristics
parameter description modified.
Table 42: ADC characteristics
conditions
modified.
Figure 33: ADC accuracy characteristics
Packages are ECOPACK® compliant.
Tables modified in
Section 5.3.5: Supply current
ADC and ANTI_TAMPER signal names modified (see
density STM32F101xx pin
STM32F101xx pin definitions
updated in
Table 21: Typical current consumption in Standby
V
modified in
Table 34: I/O static
hys
Updated:
Table 29: EMS characteristics
characteristics.
t
modified in
Table 9: Operating conditions at power-up / power-
VDD
down.
Typical values modified, note 2 modified and note 3 removed in
Low-power mode wakeup
3
Maximum current consumption
Values added and notes added in
current consumptions in Stop and Standby
On-chip peripheral current consumption on page 43
Package mechanical data inch values are calculated from mm and
rounded to 4 decimal digits (see
V
added to
Table 27: Flash memory
prog
T
added to
Table 46: TS
S_temp
T
added to
Table 11: Embedded internal reference
S_vrefint
Handling of unused pins specified in
on page
54. All I/Os are CMOS and TTL compliant.
Table 4: Medium-density STM32F101xx pin
and
Note 7
modified.
Internal LSI RC frequency changed from 32 to 40 kHz (see
oscillator
characteristics). Values added to
wakeup
timings. N
modified in
END
and data
retention.
Option byte addresses corrected in
ACC
modified in
Table 23: HSI oscillator
HSI
t
removed from
Table 26: PLL
JITTER
Appendix A: Important notes on page 71
Added:
Figure
13,
Figure
Doc ID 13586 Rev 14
Revision history
Changes
Table 31: ESD absolute maximum
Table 21: HSE 4-16 MHz oscillator
and
Table 44: ADC accuracy - limited test
modified.
characteristics.
Table 4: Medium-
definitions).
Table 4: Medium-density
modified. Note 4 removed and values
characteristics.
and
Table 30: EMI
timings.
Table
12,
Table 13
and
Table 14
Table 15: Typical and maximum
modes.
added.
Section 6: Package
characteristics).
characteristics.
characteristics.
voltage.
General input/output characteristics
definitions: table clarified
Table 25: Low-power mode
Table 28: Flash memory endurance
Figure 8: Memory
map.
characteristics.
characteristics.
added.
14,
Figure 16
and
Figure
18.
ratings.
and V
OH
mode.
Table 25:
updated.
Table 24: LSI
81/87