DSPIC33FJ64MC510T-I/PT Microchip Technology, DSPIC33FJ64MC510T-I/PT Datasheet - Page 153

• Manufacturer Part Number: DSPIC33FJ64MC510T-I/PT
• Description: IC DSPIC MCU/DSP 64K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64MC510T-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• For Use With: AC164333 - MODULE SKT FOR PM3 100QFPMA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

For example, suppose a 10 MHz crystal is being used,
with “XT with PLL” being the selected oscillator mode.
If PLLPRE<4:0> = 0, then N1 = 2. This yields a VCO
input of 10/2 = 5 MHz, which is within the acceptable
range of 0.8-8 MHz. If PLLDIV<8:0> = 0x1E, then
M = 32. This yields a VCO output of 5 x 32 = 160 MHz,
which is within the 100-200 MHz ranged needed.
If PLLPOST<1:0> = 0, then N2 = 2. This provides a
Fosc of 160/2 = 80 MHz. The resultant device operating
speed is 80/2 = 40 MIPS.
FIGURE 8-2:
TABLE 8-1:
© 2007 Microchip Technology Inc.
Fast RC Oscillator with Divide-by-N
(FRCDIVN)
Fast RC Oscillator with Divide-by-16
(FRCDIV16)
Low-Power RC Oscillator (LPRC)
Secondary (Timer1) Oscillator (SOSC)
Primary Oscillator (HS) with PLL
(HSPLL)
Primary Oscillator (XT) with PLL
(XTPLL)
Primary Oscillator (EC) with PLL
(ECPLL)
Primary Oscillator (HS)
Primary Oscillator (XT)
Primary Oscillator (EC)
Fast RC Oscillator with PLL (FRCPLL)
Fast RC Oscillator (FRC)
Note 1:
Source (Crystal, External Clock
or Internal RC)
2:
Oscillator Mode
OSC2 pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
1.6-16.0 MHz
dsPIC33F PLL BLOCK DIAGRAM
Here
PLLPRE
Oscillator Source
0.8-8.0 MHz
Divide by
Secondary
Primary
Primary
Primary
Primary
Primary
Primary
2-33
Internal
Internal
Internal
Internal
Internal
Here
Preliminary
X
EQUATION 8-3:
POSCMD<1:0>
Divide by
F
PLLDIV
CY
2-513
VCO
=
11
11
11
11
10
01
00
10
01
00
11
11
F
100-200 MHz
2
OSC
Here
=
2
1
(
10000000*32
PLLPOST
XT WITH PLL MODE
EXAMPLE
Divide by
2, 4, 8
2*2
FNOSC<2:0>
dsPIC33F
111
110
101
100
011
011
011
010
010
010
001
000
)
12.5-80 MHz
= 40 MIPS
DS70165E-page 151
Here
Note
F
1, 2
1
1
1
1
1
1
1
OSC