DSPIC33FJ64MC510T-I/PT Microchip Technology, DSPIC33FJ64MC510T-I/PT Datasheet - Page 176

• Manufacturer Part Number: DSPIC33FJ64MC510T-I/PT
• Description: IC DSPIC MCU/DSP 64K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64MC510T-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• For Use With: AC164333 - MODULE SKT FOR PM3 100QFPMA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

dsPIC33F
14.4
REGISTER 14-1:
DS70165E-page 174
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-14
bit 13
bit 12-5
bit 4
bit 3
bit 2-0
Note 1:
U-0
U-0
—
—
Output Compare Register
Refer to the device data sheet for specific time bases available to the output compare module.
Unimplemented: Read as ‘0’
OCSIDL: Stop Output Compare in Idle Mode Control bit
1 = Output Compare x will halt in CPU Idle mode
0 = Output Compare x will continue to operate in CPU Idle mode
Unimplemented: Read as ‘0’
OCFLT: PWM Fault Condition Status bit
1 = PWM Fault condition has occurred (cleared in HW only)
0 = No PWM Fault condition has occurred
(This bit is only used when OCM<2:0> = 111.)
OCTSEL: Output Compare Timer Select bit
1 = Timer3 is the clock source for Compare x
0 = Timer2 is the clock source for Compare x
OCM<2:0>: Output Compare Mode Select bits
111 = PWM mode on OCx, Fault pin enabled
110 = PWM mode on OCx, Fault pin disabled
101 = Initialize OCx pin low, generate continuous output pulses on OCx pin
100 = Initialize OCx pin low, generate single output pulse on OCx pin
011 = Compare event toggles OCx pin
010 = Initialize OCx pin high, compare event forces OCx pin low
001 = Initialize OCx pin low, compare event forces OCx pin high
000 = Output compare channel is disabled
U-0
U-0
—
—
OCxCON: OUTPUT COMPARE x CONTROL REGISTER
HC = Cleared in Hardware
W = Writable bit
‘1’ = Bit is set
OCSIDL
R/W-0
U-0
—
R-0 HC
OCFLT
Preliminary
U-0
—
(1)
HS = Set in Hardware
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
OCTSEL
R/W-0
U-0
—
(1)
R/W-0
U-0
—
© 2007 Microchip Technology Inc.
x = Bit is unknown
OCM<2:0>
R/W-0
U-0
—
R/W-0
U-0
—
bit 8
bit 0