IC MCU 8BIT OTP/EPROM 28 PSOIC

ST62T65CM6

Manufacturer Part NumberST62T65CM6
DescriptionIC MCU 8BIT OTP/EPROM 28 PSOIC
ManufacturerSTMicroelectronics
SeriesST6
ST62T65CM6 datasheet
 


Specifications of ST62T65CM6

Core ProcessorST6Core Size8-Bit
Speed8MHzConnectivitySPI
PeripheralsLED, LVD, POR, WDTNumber Of I /o21
Program Memory Size3.8KB (3.8K x 8)Program Memory TypeOTP
Eeprom Size128 x 8Ram Size128 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 13x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case28-SOIC (7.5mm Width)Controller Family/seriesST6
No. Of I/o's21Eeprom Memory Size128Byte
Ram Memory Size128ByteCpu Speed8MHz
No. Of Timers2Rohs CompliantYes
Processor SeriesST62T6xCoreST6
Data Bus Width8 bitData Ram Size128 B
Interface TypeSCIMaximum Clock Frequency8 MHz
Number Of Programmable I/os21Number Of Timers1
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 125 C
Mounting StyleSMD/SMTDevelopment Tools By SupplierST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names497-2103-5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Page 21
22
Page 22
23
Page 23
24
Page 24
25
Page 25
26
Page 26
27
Page 27
28
Page 28
29
Page 29
30
Page 30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Page 22/84

Download datasheet (2Mb)Embed
PrevNext
ST6255C ST6265C ST6265B
3.1.4 RESETS
The MCU can be reset in four ways:
– by the external Reset input being pulled low;
– by Power-on Reset;
– by the digital Watchdog peripheral timing out.
– by Low Voltage Detection (LVD)
3.1.5 RESET Input
The RESET pin may be connected to a device of
the application board in order to reset the MCU if
required. The RESET pin may be pulled low in
RUN, WAIT or STOP mode. This input can be
used to reset the MCU internal state and ensure a
correct start-up procedure. The pin is active low
and features a Schmitt trigger input. The internal
Reset signal is generated by adding a delay to the
external signal. Therefore even short pulses on
the RESET pin are acceptable, provided V
completed its rising phase and that the oscillator is
running correctly (normal RUN or WAIT modes).
The MCU is kept in the Reset state as long as the
RESET pin is held low.
If RESET activation occurs in the RUN or WAIT
modes, processing of the user program is stopped
(RUN mode only), the Inputs and Outputs are con-
figured as inputs with pull-up resistors and the
main Oscillator is restarted. When the level on the
RESET pin then goes high, the initialization se-
quence is executed following expiry of the internal
delay period.
If RESET pin activation occurs in the STOP mode,
the oscillator starts up and all Inputs and Outputs
are configured as inputs with pull-up resistors.
When the level of the RESET pin then goes high,
the initialization sequence is executed following
expiry of the internal delay period.
3.1.6 Power-on Reset
The function of the POR circuit consists in waking
up the MCU by detecting around 2V a dynamic
(rising edge) variation of the VDD Supply. At the
beginning of this sequence, the MCU is configured
in the Reset state: all I/O ports are configured as
inputs with pull-up resistors and no instruction is
executed. When the power supply voltage rises to
a sufficient level, the oscillator starts to operate,
whereupon an internal delay is initiated, in order to
allow the oscillator to fully stabilize before execut-
ing the first instruction. The initialization sequence
22/84
is executed immediately following the internal de-
lay.
To ensure correct start-up, the user should take
care that the VDD Supply is stabilized at a suffi-
cient level for the chosen frequency (see recom-
mended operation) before the reset signal is re-
leased. In addition, supply rising must start from
0V.
As a consequence, the POR does not allow to su-
pervise static, slowly rising, or falling, or noisy
(presenting oscillation) VDD supplies.
An external RC network connected to the RESET
pin, or the LVD reset can be used instead to get
the best performances.
Figure 13. Reset and Interrupt Processing
has
DD
YES
FROM RESET LOCATIONS
FETCH INSTRUCTION
RESET
NMI MASK SET
INT LATCH CLEARED
( IF PRESENT )
SELECT
NMI MODE FLAGS
PUT FFEH
ON ADDRESS BUS
IS RESET STILL
PRESENT?
NO
LOAD PC
FFE/FFF
VA000427