IC MCU 8BIT OTP/EPROM 28 PSOIC

ST62T65CM6

Manufacturer Part NumberST62T65CM6
DescriptionIC MCU 8BIT OTP/EPROM 28 PSOIC
ManufacturerSTMicroelectronics
SeriesST6
ST62T65CM6 datasheet
 


Specifications of ST62T65CM6

Core ProcessorST6Core Size8-Bit
Speed8MHzConnectivitySPI
PeripheralsLED, LVD, POR, WDTNumber Of I /o21
Program Memory Size3.8KB (3.8K x 8)Program Memory TypeOTP
Eeprom Size128 x 8Ram Size128 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 13x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case28-SOIC (7.5mm Width)Controller Family/seriesST6
No. Of I/o's21Eeprom Memory Size128Byte
Ram Memory Size128ByteCpu Speed8MHz
No. Of Timers2Rohs CompliantYes
Processor SeriesST62T6xCoreST6
Data Bus Width8 bitData Ram Size128 B
Interface TypeSCIMaximum Clock Frequency8 MHz
Number Of Programmable I/os21Number Of Timers1
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 125 C
Mounting StyleSMD/SMTDevelopment Tools By SupplierST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names497-2103-5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Page 31
32
Page 32
33
Page 33
34
Page 34
35
Page 35
36
Page 36
37
Page 37
38
Page 38
39
Page 39
40
Page 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Page 36/84

Download datasheet (2Mb)Embed
PrevNext
ST6255C ST6265C ST6265B
4 ON-CHIP PERIPHERALS
4.1 I/O PORTS
The MCU features Input/Output lines which may
be individually programmed as any of the following
input or output configurations:
– Input without pull-up or interrupt
– Input with pull-up and interrupt
– Input with pull-up, but without interrupt
– Analog input
– Push-pull output
– Open drain output
The lines are organised as bytewise Ports.
Each port is associated with 3 registers in Data
space. Each bit of these registers is associated
with a particular line (for instance, bits 0 of Port A
Data, Direction and Option registers are associat-
ed with the PA0 line of Port A).
The DATA registers (DRx), are used to read the
voltage level values of the lines which have been
configured as inputs, or to write the logic value of
the signal to be output on the lines configured as
outputs. The port data registers can be read to get
the effective logic levels of the pins, but they can
Figure 22. I/O Port Block Diagram
RESET
S
CONTROLS
IN
SHIFT
REGISTER
S
OUT
TO INTERRUPT
TO ADC
36/84
be also written by user software, in conjunction
with the related option registers, to select the dif-
ferent input mode options.
Single-bit operations on I/O registers are possible
but care is necessary because reading in input
mode is done from I/O pins while writing will direct-
ly affect the Port data register causing an unde-
sired change of the input configuration.
The Data Direction registers (DDRx) allow the
data direction (input or output) of each pin to be
set.
The Option registers (ORx) are used to select the
different port options available both in input and in
output mode.
All I/O registers can be read or written to just as
any other RAM location in Data space, so no extra
RAM cells are needed for port data storage and
manipulation. During MCU initialization, all I/O reg-
isters are cleared and the input mode with pull-ups
and no interrupt generation is selected for all the
pins, thus avoiding pin conflicts.
DATA
DIRECTION
REGISTER
DATA
REGISTER
OPTION
REGISTER
V
DD
V
DD
INPUT/OUTPUT
VA00413