IC MCU 8BIT OTP/EPROM 28 PSOIC

ST62T65CM6

Manufacturer Part NumberST62T65CM6
DescriptionIC MCU 8BIT OTP/EPROM 28 PSOIC
ManufacturerSTMicroelectronics
SeriesST6
ST62T65CM6 datasheet
 


Specifications of ST62T65CM6

Core ProcessorST6Core Size8-Bit
Speed8MHzConnectivitySPI
PeripheralsLED, LVD, POR, WDTNumber Of I /o21
Program Memory Size3.8KB (3.8K x 8)Program Memory TypeOTP
Eeprom Size128 x 8Ram Size128 x 8
Voltage - Supply (vcc/vdd)3 V ~ 6 VData ConvertersA/D 13x8b
Oscillator TypeInternalOperating Temperature-40°C ~ 85°C
Package / Case28-SOIC (7.5mm Width)Controller Family/seriesST6
No. Of I/o's21Eeprom Memory Size128Byte
Ram Memory Size128ByteCpu Speed8MHz
No. Of Timers2Rohs CompliantYes
Processor SeriesST62T6xCoreST6
Data Bus Width8 bitData Ram Size128 B
Interface TypeSCIMaximum Clock Frequency8 MHz
Number Of Programmable I/os21Number Of Timers1
Operating Supply Voltage3 V to 6 VMaximum Operating Temperature+ 125 C
Mounting StyleSMD/SMTDevelopment Tools By SupplierST62GP-EMU2, ST62E2XC-EPB/110, ST62E6XC-EPB/US, STREALIZER-II
Minimum Operating Temperature- 40 COn-chip Adc8 bit
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names497-2103-5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Page 31
32
Page 32
33
Page 33
34
Page 34
35
Page 35
36
Page 36
37
Page 37
38
Page 38
39
Page 39
40
Page 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Page 38/84

Download datasheet (2Mb)Embed
PrevNext
ST6255C ST6265C ST6265B
I/O PORTS (Cont’d)
4.1.2 Safe I/O State Switching Sequence
Switching the I/O ports from one state to another
should be done in a sequence which ensures that
no unwanted side effects can occur. The recom-
mended safe transitions are illustrated in
23. All other transitions are potentially risky and
should be avoided when changing the I/O operat-
ing mode, as it is most likely that undesirable side-
effects will be experienced, such as spurious inter-
rupt generation or two pins shorted together by the
analog multiplexer.
Single bit instructions (SET, RES, INC and DEC)
should be used with great caution on Ports Data
registers, since these instructions make an implicit
read and write back of the entire register. In port
input mode, however, the data register reads from
the input pins directly, and not from the data regis-
ter latches. Since data register information in input
mode is used to set the characteristics of the input
pin (interrupt, pull-up, analog input), these may be
unintentionally reprogrammed depending on the
state of the input pins. As a general rule, it is better
to limit the use of single bit instructions on data
registers to when the whole (8-bit) port is in output
mode. In the case of inputs or of mixed inputs and
Figure 23. Diagram showing Safe I/O State Transitions
Interrupt
pull-up
Input
pull-up (Reset
state)
Output
Open Drain
Output
Push-pull
Note *. xxx = DDR, OR, DR Bits respectively
38/84
outputs, it is advisable to keep a copy of the data
register in RAM. Single bit instructions may then
be used on the RAM copy, after which the whole
copy register can be written to the port data regis-
ter:
Figure
SET bit, datacopy
LD a, datacopy
LD DRA, a
Warning: Care must also be taken to not use in-
structions that act on a whole port register (INC,
DEC, or read operations) when all 8 bits are not
available on the device. Unavailable bits must be
masked by software (AND instruction).
The WAIT and STOP instructions allow the
ST62xx to be used in situations where low power
consumption is needed. The lowest power con-
sumption is achieved by configuring I/Os in input
mode with well-defined logic levels.
The user must take care not to switch outputs with
heavy loads during the conversion of one of the
analog inputs in order to avoid any disturbance to
the conversion.
010*
011
000
001
100
101
110
111
Input
Analog
Input
Output
Open Drain
Output
Push-pull