MCF5282CVF80 Freescale Semiconductor, MCF5282CVF80 Datasheet - Page 131

• Manufacturer Part Number: MCF5282CVF80
• Description: IC MPU 32BIT 66MHZ 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVF80

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Digital Ic Case Style: MAPBGA
• Rohs Compliant: No
• Package: 256MA-BGA
• Device Core: ColdFire
• Family Name: MCF528x
• Maximum Speed: 80 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 150
• Interface Type: CAN/Ethernet/I2C/QSPI/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 12
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

The Flash state machine flags errors in command write sequences by means of the ACCERR and PVIOL
flags in the CFMUSTAT register. An erroneous command write sequence self-aborts and sets the
appropriate flag. The ACCERR or PVIOL flags must be cleared before commencing another command
write sequence.
A summary of the programming algorithm is shown in
verify algorithms with the exceptions noted in step 1 above.
6.4.3.3
Table 6-13
Freescale Semiconductor
2. Write the program, erase, or verify command to CFMCMD, the command buffer. See
3. Launch the command by writing a 1 to the CBEIF flag. This clears CBEIF. When command
Section 6.4.3.3, “Flash Valid
execution is complete, the Flash state machine sets the CCIF flag. The CBEIF flag is also set
again, indicating that the address, data, and command buffers are ready for a new command
sequence to begin.
summarizes the valid Flash user commands.
Flash Valid Commands
CFMCMD
The page erase command operates simultaneously on adjacent erase pages
in two interleaved Flash physical blocks. Thus, a single erase page is
effectively 2 Kbyte.
By writing a 0 to CBEIF, a command sequence can be aborted after the
longword write to the CFM array or the command write to the CFMCMD
and before the command is launched. The ACCERR flag will be set on
aborted commands and must be cleared before a new command write
sequence.
0x05
0x20
0x40
0x41
0x06
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
Page erase
Meaning
Program
Erase
erase
erase
verify
Page
Mass
verify
Table 6-13. Flash User Commands
Commands.”
Verify that all 256 Kbytes of Flash from two interleaving physical
blocks are erased. If both blocks are erased, the BLANK bit will
be set in the CFMUSTAT register upon command completion.
Program a 32-bit longword.
Erase 2 Kbyte of Flash. Two 1024-byte pages from interleaving
physical blocks are erased in this operation.
Erase all 256 Kbytes of Flash from two interleaving physical
blocks. A mass erase is only possible when no PROTECT bits
are set for that block.
Verify that the two 1024-byte pages are erased. If both pages
are erased, the BLANK bit will be set in the CFMUSTAT register
upon command completion.
NOTE
NOTE
Figure
Description
6-13. The flow is similar for the erase and
ColdFire Flash Module (CFM)
6-19