ST72T511R9T6 STMicroelectronics, ST72T511R9T6 Datasheet - Page 89

• Manufacturer Part Number: ST72T511R9T6
• Description: Microcontrollers (MCU) UV EPROM 60K SPI/SCI
• Manufacturer: STMicroelectronics

Specifications of ST72T511R9T6

• Data Bus Width: 8 bit
• Program Memory Type: EEPROM
• Program Memory Size: 60 KB
• Data Ram Size: 2048 B
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 5
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-64
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / Rohs Status: No

SERIAL PERIPHERAL INTERFACE (Cont’d)
10.5.7 Register Description
CONTROL REGISTER (CR)
Read/Write
Reset Value: 0000xxxx (0xh)
Bit 7 = SPIE Serial peripheral interrupt enable.
This bit is set and cleared by software.
0: Interrupt is inhibited
1: An SPI interrupt is generated whenever SPIF=1
Bit 6 = SPE Serial peripheral output enable.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see Section 10.5.4.5 ”Master Mode Fault” on
page 85).
0: I/O port connected to pins
1: SPI alternate functions connected to pins
The SPE bit is cleared by reset, so the SPI periph-
eral is not initially connected to the external pins.
Bit 5 = SPR2 Divider Enable .
this bit is set and cleared by software and it is
cleared by reset. It is used with the SPR[1:0] bits to
set the baud rate. Refer to Table 20.
0: Divider by 2 enabled
1: Divider by 2 disabled
Bit 4 = MSTR Master.
This bit is set and cleared by software. It is also
cleared by hardware when, in master mode, SS=0
(see Section 10.5.4.5 ”Master Mode Fault” on
page 85).
0: Slave mode is selected
1: Master mode is selected, the function of the
SPIE
7
or MODF=1 in the SR register
SCK pin changes from an input to an output and
the functions of the MISO and MOSI pins are re-
versed.
SPE SPR2
MSTR
CPOL
CPHA
SPR1
SPR0
0
ST72311R, ST72511R, ST72512R, ST72532R
Bit 3 = CPOL Clock polarity.
This bit is set and cleared by software. This bit de-
termines the steady state of the serial Clock. The
CPOL bit affects both the master and slave
modes.
0: The steady state is a low value at the SCK pin.
1: The steady state is a high value at the SCK pin.
Bit 2 = CPHA Clock phase.
This bit is set and cleared by software.
0: The first clock transition is the first data capture
1: The second clock transition is the first capture
Bit 1:0 = SPR[1:0] Serial peripheral rate.
These bits are set and cleared by software.Used
with the SPR2 bit, they select one of six baud rates
to be used as the serial clock when the device is a
master.
These 2 bits have no effect in slave mode.
Table 20. Serial Peripheral Baud Rate
edge.
edge.
Serial Clock
f
f
f
f
CPU
f
f
CPU
CPU
CPU
CPU
CPU
/128
/16
/32
/64
/2
/8
SPR2
1
0
0
1
0
0
SPR1
0
0
0
1
1
1
89/164
SPR0
0
0
1
0
0
1