AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 135

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

9.4.3
9.4.4
9.4.5
9.5
9.5.1
9.5.1.1
32117C–AVR-08/11
Functional Description
Interrupt
Peripheral Events
Debug Operation
Initialization
Enabling and disabling the AST clock
The AST interrupt request lines are connected to the interrupt controller. Using the AST inter-
rupts requires the interrupt controller to be programmed first.
The AST peripheral events are connected via the Peripheral Event System. Refer to the Periph-
eral Event System chapter for details.
The AST prescaler and counter is frozen during debug operation, unless the Run In Debug bit in
the Development Control Register is set and the bit corresponding to the AST is set in the
Peripheral Debug Register (PDBG). Please refer to the On-Chip Debug chapter in the
AVR32UC Technical Reference Manual, and the OCD Module Configuration section, for details.
If the AST is configured in a way that requires it to be periodically serviced by the CPU through
interrupts or similar, improper operation or data loss may result during debugging.
Before enabling the AST, the internal AST clock CLK_AST_PRSC must be enabled, following
the procedure specified in
(CLOCK.CSSEL) selects the source for this clock. The Clock Enable bit in the Clock register
(CLOCK.CEN) enables the CLK_AST_PRSC.
When CLK_AST_PRSC is enabled, the AST can be enabled by writing a one to the Enable bit in
the Control Register (CR.EN).
The Clock Source Selection field (CLOCK.CSSEL) and the Clock Enable bit (CLOCK.CEN) can-
not be changed simultaneously. Special procedures must be followed for enabling and disabling
the CLK_AST_PRSC and for changing the source for this clock.
To enable CLK_AST_PRSC:
To disable the clock:
• Peripheral Bus clock (PB clock). This is the clock of the peripheral bus the AST is connected
• Generic clock (GCLK). One of the generic clocks is connected to the AST. This clock must be
• Write the selected value to CLOCK.CSSEL
• Wait until SR.CLKBUSY reads as zero
• Write a one to CLOCK.CEN, without changing CLOCK.CSSEL
• Wait until SR.CLKBUSY reads as zero
• Write a zero to CLOCK.CEN to disable the clock, without changing CLOCK.CSSEL
• Wait until SR.CLKBUSY reads as zero
to.
enabled before use, and remains enabled in sleep modes when the PB clock is active.
Section
9.5.1.1. The Clock Source Select field in the Clock register
AT32UC3C
135