MC68HC711xxxx Motorola, MC68HC711xxxx Datasheet - Page 219
MC68HC711xxxx
Manufacturer Part Number
MC68HC711xxxx
Description
Microcontrollers
Manufacturer
Motorola
Datasheet
1.MC68HC711XXXX.pdf
(268 pages)
- Current page: 219 of 268
- Download datasheet (4Mb)
AN1060 — Rev. 1.0
MOTOROLA
M68HC11 Family members which have 256 bytes of RAM, the download
length is fixed at exactly 256 bytes plus the leading $FF character.
The intercharacter delay counter is started [8] by loading the delay
constant from TOC1 into the X index register. The 19-E-cycle wait loop
is executed repeatedly until either a character is received [9] or the
allowed intercharacter delay time expires [10]. For 7812 baud, the delay
constant is 10,241 E cycles (539 x 19 E cycles per loop). Four character
times at 7812 baud is 10,240 E cycles (baud prescale of 4 x baud divider
of 4 x 16 internal SCI clocks/bit time x 10 bit times/character x 4
character times). The delay from reset to the initial $FF character is not
critical since the delay counter is not started until after the first character
($FF) is received.
To terminate the bootloading sequence and jump to the start of RAM
without downloading any data to the on-chip RAM, simply send $FF and
nothing else. This feature is similar to the jump to EEPROM at [4] except
the $FF causes a jump to the start of RAM. This procedure requires that
the RAM has been loaded with a valid program since it would make no
sense to jump to a location in uninitialized memory.
After receiving a character, the downloaded byte is stored in RAM [11].
The data is transmitted back to the host [12] as an indication that the
download is progressing normally. At [13], the RAM pointer is
incremented to the next RAM address. If the RAM pointer has not
passed the end of RAM, the main download loop (from [7] to [14]) is
repeated.
When all data has been downloaded, the bootloader goes to [16]
because of an intercharacter delay timeout [10] or because the entire
512-byte RAM has been filled [15]. At [16], the X and Y index registers
are set up for calling the PROGRAM utility routine, which saves the user
from having to do this in a downloaded program. The PROGRAM utility
is fully explained in
bootloader program is to jump to the start of RAM [17], which starts the
user’s downloaded program.
EPROM Programming
Utility. The final step of the
Application Note
219
Related parts for MC68HC711xxxx
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
3N2046367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MOTOROLA POWERPC 603e MICROPROCESSOR
Manufacturer:
Motorola
Part Number:
Description:
Motorola Semiconductor Datasheet Library
Manufacturer:
Motorola
Part Number:
Description:
SWITCHMODE Schottky Power Rectifier(POWERTAP III Package)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SWITCHMODE Schottky Power Rectifirer
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Search -----> MTE53N50E
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
NPN SILICON POWER DARLINGTON TRANSISTOR
Manufacturer:
Motorola
Datasheet: