IBM25PPC440GP IBM Microelectronics, IBM25PPC440GP Datasheet - Page 70
IBM25PPC440GP
Manufacturer Part Number
IBM25PPC440GP
Description
PowerPC 440GP Embedded Processor
Manufacturer
IBM Microelectronics
Datasheet
1.IBM25PPC440GP.pdf
(72 pages)
- Current page: 70 of 72
- Download datasheet (2Mb)
Initialization
The PPC440GP provides the option for setting initial parameters based on default values or by reading them
from a slave PROM attached to the IIC0 bus (see “EEPROM” below). Some of the default values can be
altered by strapping on external pins (see “Strapping” below).
Strapping
While the SysReset input pin is low (system reset), the state of certain I/O pins is read to enable certain
default initial conditions prior to PPC440GP start-up. The actual capture instant is the nearest reference clock
edge before the deassertion of reset. These pins must be strapped using external pull-up (logical 1) or pull-
down (logical 0) resistors to select the desired default conditions. They are used for strap functions only
during reset. Following reset they are used for normal functions.
The following table lists the strapping pins along with their functions and strapping options:
EEPROM
During reset, initial conditions other than those obtained from the strapping pins can be read from a ROM
device connected to the IIC0 port. At the de-assertion of reset, if the bootstrap controller is enabled, the
PPC440GP sequentially reads 16 bytes from the ROM device on the IIC0 port and uses the first 8 bytes to set
the SYS0 and SYS1 registers accordingly. Otherwise, the default values set in the STRP0 and STRP1
registers are used for initialization.
The initialization settings and their default values are covered in detail in the PowerPC 440GP Embedded
Processor User’s Manual.
Page 70 of 72
Strapping Pin Assignments
Bootstrap controller
IIC0 slave address that will respond with boot data
Function
PowerPC 440GP Embedded Processor Data Sheet
Enabled
Disabled
Option
0x54
0x50
Ball Strapping
(UART0_DCD)
(UART0_DSR)
V24
V02
0
1
0
1
5/13/04
Related parts for IBM25PPC440GP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MPU 750xx RISC 32-Bit 0.13um 600MHz 1.8V/2.5V/3.3V 750-Pin CBGA Tray
Manufacturer:
IBM MICROELECTRONICS
Datasheet:
Part Number:
Description:
MPU PowerPC750 RISC 64-Bit 0.2um 366MHz 1.8V/2.5V/3.3V 360-Pin CBGA Tray
Manufacturer:
IBM MICROELECTRONICS
Part Number:
Description:
Manufacturer:
IBM Microelectronics
Datasheet:
Part Number:
Description:
MPEG S422, MPEG S420 and MPEG SI Encoders
Manufacturer:
IBM Microelectronics
Part Number:
Description:
32-Bit RISC Embedded Controller
Manufacturer:
IBM Microelectronics
Datasheet:
Part Number:
Description:
32-Bit RISC Embedded Controller
Manufacturer:
IBM Microelectronics
Datasheet:
Part Number:
Description:
8Mb (256Kx36 & 512x18) and 4Mb (128Kx36 & 256K x 18) SRAM
Manufacturer:
IBM Microelectronics
Part Number:
Description:
Microprocessor, PowerPC 405EP Embedded Processor Data Sheet
Manufacturer:
IBM Microelectronics
Datasheet:
Part Number:
Description:
PowerPC 602 RISC Microprocessor
Manufacturer:
IBM Microelectronics
Part Number:
Description:
Controller, Digital Set-Top Box Integrated Controllers
Manufacturer:
IBM Microelectronics
Part Number:
Description:
Controller, Digital Set-Top Box Integrated Controllers
Manufacturer:
IBM Microelectronics
Part Number:
Description:
Decoder and Demux, A/V Transport/Decoders
Manufacturer:
IBM Microelectronics