16F876 Microchip Technology, 16F876 Datasheet - Page 126

• Manufacturer Part Number: 16F876
• Description: 28/40-pin 8-Bit CMOS FLASH Microcontrollers
• Manufacturer: Microchip Technology

PIC16F87X
12.4
A Power-on Reset pulse is generated on-chip when
V
take advantage of the POR, tie the MCLR pin directly
(or through a resistor) to V
nal RC components usually needed to create a Power-
on Reset. A maximum rise time for V
See Electrical Specifications for details.
When the device starts normal operation (exits the
reset condition), device operating parameters (voltage,
frequency, temperature,...) must be met to ensure oper-
ation. If these conditions are not met, the device must
be held in reset until the operating conditions are met.
Brown-out Reset may be used to meet the start-up con-
ditions. For additional information, refer to Application
Note,
(DS00007).
12.5
The Power-up Timer provides a fixed 72 ms nominal
time-out on power-up only from the POR. The Power-
up Timer operates on an internal RC oscillator. The
chip is kept in reset as long as the PWRT is active. The
PWRT’s time delay allows V
level. A configuration bit is provided to enable/disable
the PWRT.
The power-up time delay will vary from chip to chip due
to V
parameters for details (T
12.6
The Oscillator Start-up Timer (OST) provides 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over. This ensures that the crystal oscil-
lator or resonator has started and stabilized.
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset or wake-up from
SLEEP.
12.7
The configuration bit, BODEN, can enable or disable
the Brown-out Reset circuit. If V
(parameter D005, about 4V) for longer than T
(parameter #35, about 100 S), the brown-out situa-
tion will reset the device. If V
less than T
Once the brown-out occurs, the device will remain in
brown-out reset until V
power-up timer then keeps the device in reset for
T
fall below V
process will restart when V
the power-up timer reset. The power-up timer is
always enabled when the brown-out reset circuit is
enabled regardless of the state of the PWRT configu-
ration bit.
DS30292B-page 126
PWRT
DD
DD
rise is detected (in the range of 1.2V - 1.7V). To
, temperature and process variation. See DC
(parameter #33, about 72mS). If V
AN007,
Power-On Reset (POR)
Power-up Timer (PWRT)
Oscillator Start-up Timer (OST)
Brown-Out Reset (BOR)
BOR
BOR
, a reset may not occur.
during T
“Power-up
PWRT
DD
DD
PWRT
DD
DD
. This will eliminate exter-
rises above V
, parameter #33).
DD
to rise to an acceptable
rises above V
, the brown-out reset
Trouble
DD
falls below V
falls below V
DD
is specified.
Shooting”,
DD
BOR
BOR
BOR
should
. The
with
BOR
BOR
for
12.8
On power-up, the time-out sequence is as follows: The
PWRT delay starts (if enabled) when a POR reset
occurs. Then OST starts counting 1024 oscillator
cycles when PWRT ends (LP, XT, HS). When the OST
ends, the device comes out of RESET.
If MCLR is kept low long enough, the time-outs will
expire. Bringing MCLR high will begin execution imme-
diately. This is useful for testing purposes or to synchro-
nize more than one PIC16CXX device operating in
parallel.
Table 12-5 shows the reset conditions for the STATUS,
PCON and PC registers, while Table 12-6 shows the
reset conditions for all the registers.
12.9
The Power Control/Status Register, PCON, has up to
two bits depending upon the device.
Bit0 is Brown-out Reset Status bit, BOR. Bit BOR is
unknown on a Power-on Reset. It must then be set by
the user and checked on subsequent resets to see if bit
BOR cleared, indicating a BOR occurred. The BOR bit
is a "don’t care" bit and is not necessarily predictable if
the Brown-out Reset circuitry is disabled (by clearing
bit BODEN in the Configuration Word).
Bit1 is POR (Power-on Reset Status bit). It is cleared on
a Power-on Reset and unaffected otherwise. The user
must set this bit following a Power-on Reset.
Time-out Sequence
Power Control/Status Register
(PCON)
1999 Microchip Technology Inc.