ATMEGA16U2-MU Atmel, ATMEGA16U2-MU Datasheet - Page 196

• Manufacturer Part Number: ATMEGA16U2-MU
• Description: MCU AVR 16K FLASH USB 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U2-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: AVR8
• Processor Series: ATMEGA16x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 16 MHz
• Data Ram Size: 1.25 KB
• Data Rom Size: 512 B
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: SPI, UART
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

20.10.3
7799D–AVR–11/10
REGCR – Regulator Control Register
buffers.
Table 20-2.
• Bit 5:4 – UPDRV[1:0]: USB direct drive values
These bits are relevant only when one of the direct drive modes for USB is enable. When
UPWE[1:0] is 1:0 the values of these bits are output to USB.
The value written to UPDRV1 is output to D+.
The value written to UPDRV0 is output to D-.
• Bits 3:2 – Res: Reserved
These bits are reserved and should always read as zero.
• Bit 1 – DPI: D+ Input value
This bit is read only, the value read from this bit reflects the D+ pin (USB buffer). This bit is set
one by hardware if a one logic level is read on D+. This bit is set to zero by hardware if a zero
logic level is read on D+.
• Bit 0 – DMI: D- Input value
This bit is read only, the value read from this bit reflects the D- pin (USB buffer). This bit is set
one by hardware if a logic one is read on D-. This bit is set to zero by hardware if a logic zero
logic is read on D-.
• Bit 0 – REGDIS: Regulator Disable
Writing this bit to a logic one disables the internal 3.3V regulator. Writing this bit to a logic zero
enables the regulstor.
Bit
(0x63)
Read/Write
Initial Value
UPWE1
0
0
1
1
UPWE[I:0] Bits Settings
R
7
0
-
R
6
0
-
UPWE0
R
5
0
-
0
1
0
1
R
4
0
-
Direct drive is disabled.
Reserved
Direct drive of DP/DM (UPDRV[1:0] values)
Reserved
Mode
ATmega8U2/16U2/32U2
R
3
0
-
R
2
0
-
R
1
0
-
REGDIS
R/W
0
0
REGCR
196