ATMEGA16U2-MU Atmel, ATMEGA16U2-MU Datasheet - Page 30

• Manufacturer Part Number: ATMEGA16U2-MU
• Description: MCU AVR 16K FLASH USB 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U2-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: AVR8
• Processor Series: ATMEGA16x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 16 MHz
• Data Ram Size: 1.25 KB
• Data Rom Size: 512 B
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: SPI, UART
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

8.4
7799D–AVR–11/10
Low Power Crystal Oscillator
The oscillator is required to oscillate for a minimum number of cycles before the clock is consid-
ered stable. An internal ripple counter monitors the oscillator output clock, and keeps the internal
reset active for a given number of clock cycles. The reset is then released and the device will
start to execute. The recommended oscillator start-up time is dependent on the clock type, and
varies from 6 cycles for an externally applied clock to 32K cycles for a low frequency crystal.
The start-up sequence for the clock includes both the time-out delay and the start-up time when
the device starts up from reset. When starting up from Power-save or Power-down mode, Vcc is
assumed to be at a sufficient level and only the start-up time is included.
Pins XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be
configured for use as an On-chip Oscillator, as shown in
ceramic resonator may be used.
This Crystal Oscillator is a low power oscillator, with reduced voltage swing on the XTAL2 out-
put. It gives the lowest power consumption, but is not capable of driving other clock inputs, and
may be more susceptible to noise in noisy environments.
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the
capacitors depends on the crystal or resonator in use, the amount of stray capacitance, and the
electromagnetic noise of the environment. Some initial guidelines for choosing capacitors for
use with crystals are given in
the manufacturer should be used.
Figure 8-4.
The Low Power Oscillator can operate in three different modes, each optimized for a specific fre-
quency range. The operating mode is selected by the fuses CKSEL3..1 as shown in
Table 8-3.
Notes:
Frequency Range
1. The frequency ranges are preliminary values. Actual values are TBD.
2. This option should not be used with crystals, only with ceramic resonators.
8.0 - 16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
Crystal Oscillator Connections
Low Power Crystal Oscillator Operating Modes
(1)
(MHz)
Table
8-3. For ceramic resonators, the capacitor values given by
C2
C1
CKSEL3..1
100
101
110
111
(2)
ATmega8U2/16U2/32U2
Recommended Range for Capacitors C1
Figure
XTAL2
XTAL1
GND
(3)
8-4. Either a quartz crystal or a
and C2 (pF)
12 - 22
12 - 22
12 - 22
–
Table
8-3.
30